Operating and installation instructions
Ceramic hobs with induction
KM 5941 / 5942 / 5943 / 5944
KM 5945 / 5946 / 5947 / 5948
KM 5951 / 5952 / 5953 / 5954
KM 5955 / 5956 / 5957 / 5958
KM 5975 / 5985 / 5986
en - GB
To avoid the risk of accidents or
damage to the appliance it is
essential to read these
instructions before it is installed
and used for the first time.
M.-Nr. 07 257 390
Contents
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Minute minder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
To switch a cooking zone off automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
To use both timer functions at the same time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Safety lock/System lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Stop and Go. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Safety switch-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Safety instructions for installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Hob with frame or bevelled edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
General installation tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Flush-fitted hobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
After sales service, data plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
3
Guide to the appliance
KM 5941
aCooking zone with Twin Booster
bcd Cooking zones with Single Booster
eCooking zone controls and displays (see “Cooking zone controls and displays”)
fTimer control and display (see “Timer control and display”)
gSafety lock indicator lamp
hSafety lock sensor switch
iHob ON/OFF sensor switch
4
Guide to the appliance
KM 5942 / KM 5943 / KM 5944
abd Cooking zones with Single Booster
cCooking zone with Twin Booster
eCooking zone controls and displays (see “Cooking zone controls and displays”)
fTimer control and display (see “Timer control and display”)
gSafety lock indicator lamp
hSafety lock sensor switch
iHob ON/OFF sensor switch
5
Guide to the appliance
KM 5945
ac Cooking zones with Twin Booster
bd Cooking zones with Single Booster
eCooking zone controls and displays (see “Cooking zone controls and displays”)
fTimer control and display (see “Timer control and display”)
gSafety lock indicator lamp
hSafety lock sensor switch
iHob ON/OFF sensor switch
6
Guide to the appliance
KM 5946 / KM 5947 / KM 5948
aCooking zone with Twin Booster
bc Cooking zones with Single Booster
dCooking zone controls and displays (see “Cooking zone controls and displays”)
eTimer control and display (see “Timer control and display”)
fSafety lock indicator lamp
gSafety lock sensor switch
hHob ON/OFF sensor switch
7
Guide to the appliance
KM 5951 / KM 5952 / KM 5953
aCooking zone with Twin Booster
bcd Cooking zones with Single Booster
eCooking zone controls and displays (see “Cooking zone controls and displays”)
fTimer control and display (see “Timer control and display”)
gSafety lock indicator lamp
hSafety lock sensor switch
iHob ON/OFF sensor switch
8
Guide to the appliance
KM 5954
aCooking zone with Twin Booster
bcd Cooking zones with Single Booster
eCooking zone controls and displays (see “Cooking zone controls and displays”)
fTimer control and display (see “Timer control and display”)
gSafety lock indicator lamp
hSafety lock sensor switch
iHob ON/OFF sensor switch
9
Guide to the appliance
KM 5955 / KM 5956 / KM 5986
ac Cooking zones with Twin Booster
bd Cooking zones with Single Booster
eCooking zone controls and displays (see “Cooking zone controls and displays”)
fTimer control and display (see “Timer control and display”)
gSafety lock indicator lamp
hSafety lock sensor switch
iHob ON/OFF sensor switch
10
Guide to the appliance
KM 5957
ac Cooking zones with Twin Booster
bd Cooking zones with Single Booster
eCooking zone controls and displays (see “Cooking zone controls and displays”)
fTimer control and display (see “Timer control and display”)
gSafety lock indicator lamp
hSafety lock sensor switch
iHob ON/OFF sensor switch
11
Guide to the appliance
KM 5958
ac Cooking zones with Twin Booster
bCooking zone with Single Booster
dCooking zone controls and displays (see “Cooking zone controls and displays”)
eTimer control and display (see “Timer control and display”)
fSafety lock indicator lamp
gSafety lock sensor switch
hHob ON/OFF sensor switch
12
Guide to the appliance
KM 5975 / KM 5985
aCooking zone with Twin Booster
bcd Cooking zones with Single Booster
eCooking zone controls and displays (see “Cooking zone controls and displays”)
fTimer control and display (see “Timer control and display”)
gSafety lock indicator lamp
hSafety lock sensor switch
iHob ON/OFF sensor switch
13
Guide to the appliance
Cooking zone sensors and displays
(Example)
aDisplays:
0
= Cooking zone ready for use
= Keeping warm function
= Power levels
^
1 to 9
I
= Single Booster
II
#
ß
= Twin Booster
= Residual heat
= No pan on cooking zone or pan unsuitable
(see "Induction")
F
= Fault (see "Safety switch-off")
= Auto heat-up when the power setting range has been extended
A
P0 etc. = Programme (see "Programming")
S0 etc. = Status (see "Programming")
bIndicator lamp for Auto heat-up or extended power setting (see "Programming"),
e.g. the front left cooking zone
cIndicator lamp for Booster
dSensor switch for Booster
ePower setting sensor switches
14
Guide to the appliance
Timer control and display
aSensor switch for activating the timer, switching between functions and
selecting automatic switch-off for a cooking zone
bSensor switches for setting the time
cTime display
dIndicator lamp for automatic switch-off, e.g. of the rear right cooking zone
eControl lamp for minute minder
fControl lamp for half hours with a minute minder time of more than 99 minutes
15
Guide to the appliance
Cooking zones
Cooking
zone
KM 5941 / KM 5951 / KM 5952 / KM 5953
Minimum to maximum
Rating in watts for 230 V**
C in cm*
y
16 - 23
normal:
2300
3000
3700
with Single Booster I:
with Twin Booster II:
w
x
z
10 - 16
14 - 20
14 - 20
normal:
1400
1800
with Booster:
normal:
1850
2900
with Booster:
normal:
1850
2900
with Booster:
Total:
7400
Cooking
zone
KM 5942 / KM 5943 / KM 5944
Minimum to maximum Rating in watts for 230 V**
C in cm*
y
w
x
14 - 20
normal:
1850
2900
with Booster:
10 - 16
16 - 23
normal:
1400
1800
with Booster:
normal:
2300
3000
3700
with Single Booster I:
with Twin Booster II:
z
10 - 16
normal:
1400
1800
with Booster:
Total:
7400
* Pans with a base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
16
Guide to the appliance
Cooking
zone
KM 5945 / KM 5955 / KM 5956 / 5986
Minimum to maximum
Rating in watts for 230 V**
C in cm*
y
16 - 23
normal:
2300
3000
3700
with Single Booster I:
with Twin Booster II:
w
x
10 - 16
normal:
1400
1800
with Booster:
14 - 20 /
20 x 30
normal:
1850
2300
2400
3000
3700
with Single/Twin Booster I/II:
normal:
with Single Booster I:
with Twin Booster II:
z
14 - 20
normal:
1850
2900
with Booster:
Total:
7400
Cooking zone
KM 5946 / KM 5947 / KM 5948
Minimum to maximum Rating in watts for 230 V**
C in cm*
f
18 - 28
normal:
2400
3000
3700
with Single Booster I:
with Twin Booster II:
x
z
14 - 20
10 - 16
normal:
1850
2900
with Booster:
normal:
1400
1800
with Booster:
Total:
7400
* Pans with a base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
17
Guide to the appliance
Cooking
KM 5954
Rating in watts for 230 V**
zone
Minimum to maximum
C in cm*
y
18 - 28
normal:
2400
3000
3700
with Single Booster I:
with Twin Booster II:
w
x
z
10 - 16
14 - 20
14 - 20
normal:
1400
1800
with Booster:
normal:
1850
2900
with Booster:
normal:
1850
2900
with Booster:
Total:
7400
Cooking
zone
KM 5957
Minimum to maximum
Rating in watts for 230 V**
C in cm*
y
18 - 28
normal:
2400
3000
3700
with Single Booster I:
with Twin Booster II:
w
x
10 - 16
normal:
1400
1800
with Booster:
14 - 20 /
20 x 30
normal:
1850
2300
2400
3000
3700
with Single/Twin Booster I/II:
normal:
with Single Booster I:
with Twin Booster II:
z
14 - 20
normal:
1850
2900
with Booster:
Total:
7400
* Pans with a base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
18
Guide to the appliance
Cooking zone
KM 5958
Rating in watts for 230 V**
Minimum to maximum
C in cm*
f
18 - 28
normal:
2400
3000
3700
with Single Booster I:
with Twin Booster II:
x
z
10 - 16
normal:
1400
1800
with Booster:
14 - 20 /
20 x 30
normal:
1850
2300
2400
3000
3700
with Single/Twin Booster I/II:
normal:
with Single Booster I:
with Twin Booster II:
Total:
7400
Cooking zone
KM 5975 / 5985
Minimum to maximum
Rating in watts for 230 V**
C in cm*
Left
16 - 23
normal:
2300
3000
3700
with Single Booster I:
with Twin Booster II:
Centre left
Centre right
Right
10 - 16
14 - 20
14 - 20
normal:
1400
1800
with Booster:
normal:
1850
2900
with Booster:
normal:
1850
2900
with Booster:
Total:
7400
* Pans with a base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
Special feature
Hobs bearing the < symbol in the top left-hand corner are suitable for connecting
to the Miele|home system (see "Optional accessories").
19
Warning and safety instructions
Correct application
This appliance complies with all
relevant local and national safety
requirements. Improper use of the
appliance can, however, present a
risk of both personal injury and
material damage.
This appliance is intended for
~
domestic use for the preparation of
food only.
Any other usage is at the owner's risk
and could be dangerous. The
manufacturer cannot be held liable for
damage resulting from incorrect or
improper use of the appliance.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before installation and before using
it for the first time.
This appliance is not intended for
~
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
They contain important notes on the
installation, safety, operation and
care of the appliance.
experience or knowledge, unless they
are supervised whilst using it or have
been shown how to use it by a person
responsible for their safety.
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner.
20
Warning and safety instructions
Safety with children
Keep all pans out of reach of
~
children. Turn pan handles inwards
away from the edge of the hob. Danger
of burning or scalding. Special hob
guards are available from good retail
outlets.
Use the safety lock to prevent
~
children operating the appliance or
altering the settings.
Keep children away from the
~
appliance at all times. It is not a toy! To
avoid the risk of injury, do not allow
them to play with it or use the controls.
They will not understand the potential
dangers posed by it. They should be
supervised whenever you are working
in the kitchen.
Packaging, e.g. cling film,
~
polystyrene and plastic wrappings,
must be kept out of the reach of babies
and young children. Danger of
suffocation. Dispose of or recycle all
packaging safely as soon as possible.
Older children may use the
~
appliance only when its operation has
been clearly explained to them and
they are able to use it safely,
recognising the dangers of misuse.
They must be aware of the potential
dangers caused by incorrect operation.
The appliance gets hot when in use
~
and remains hot for quite a while after
being switched off. To safeguard
against burning, keep children well
away from the appliance at all times.
Do not store anything which might
~
arouse a child's interest in storage
areas above or next to the appliance.
Otherwise they could be tempted into
climbing onto the appliance with the
risk of burning themselves.
21
Warning and safety instructions
Technical safety
Never open the housing of the
~
appliance.
Before installation, check the
~
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user and can
cause operational faults.
appliance for visible signs of damage.
Do not install and use a damaged
appliance. A damaged appliance is
dangerous.
Installation, maintenance and
~
The electrical safety of this
~
repairs may only be carried out by a
suitably qualified and competent
person in strict accordance with current
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
appliance can only be guaranteed
when continuity is complete between it
and an effective earthing system which
complies with local and national safety
regulations. It is most important that this
basic safety requirement is present and
regularly tested, and where there is any
doubt, the household wiring system
should be inspected by a qualified
During installation, maintenance and
~
electrician. The manufacturer cannot be repair work, the appliance must be
held liable for the consequences of an
inadequate earthing system (e.g.
electric shock).
disconnected from the mains electricity
supply. It is only completely isolated
from the electricity supply when:
Before connecting the appliance,
– the mains fuse is disconnected,
~
make sure that the connection data on
the data plate (voltage and connected
load) match the mains electricity
supply.
– the screw-out fuse is removed (in
countries where this is applicable),
– it is switched off at the wall socket
and the plug is withdrawn from the
socket, or it is switched off at the
isolator.
This data must correspond in order to
avoid the risk of damage to the
appliance. Consult a qualified
electrician if in any doubt.
For safety reasons, this appliance
~
may only be used after it has been built
in.
22
Warning and safety instructions
While the appliance is under
Correct use
~
guarantee, repairs should only be
undertaken by a service technician
authorised by the manufacturer.
For people fitted with a heart
~
pacemaker:
Please note that the area immediately
Otherwise the guarantee is invalidated.
surrounding the hob is
Faulty components must only be
~
replaced by genuine Miele original
electromagnetically charged, and that it
is very unlikely to affect a pacemaker.
spare parts. The manufacturer can only However, if in any doubt, consult the
guarantee the safety of the appliance
when Miele replacement parts are
used.
manufacturer of the pacemaker or your
doctor.
To prevent damage to items which
~
If the connection cable is damaged, are susceptible to magnetic fields, e.g.
~
it must be replaced by a suitably
credit cards, diskettes, pocket
calculators etc, do not leave them in the
immediate vicinity of the hob.
qualified electrician with a specialist
connection cable of type H 05 VV-F
(pvc insulated), available from the Miele
Spare Parts Department.
The appliance gets hot when in use
~
and remains hot for quite a while after
being switched off. There is a danger of
burning until the residual heat
indicators go out.
Do not connect the appliance to the
~
mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
Do not leave the appliance
~
unattended whilst it is in use.
Pans that have boiled dry can cause
damage to the ceramic surface for
which the manufacturer cannot be held
liable.
Do not use the hob if the ceramic
~
surface is cracked, chipped or
damaged in any way. Switch it off im-
mediately, and disconnect it from the
mains electricity supply. Danger of
electric shock.
Boiling fat or oil could ignite and cause
a fire.
If, despite this, oil or fat does catch
~
In countries where there are areas
fire, do not attempt to put out the flames
with water. Use a suitable fire blanket,
saucepan lid, damp towel or similar to
smother the flames.
~
which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any
damage caused by cockroaches or
other vermin will not be covered by the
guarantee.
23
Warning and safety instructions
For added protection, it is advisable
Do not heat up unopened tins of
~
food on the hob, as pressure will build
~
to use heat-resistant pot holders or
gloves when using the appliance. Do
not let them get damp or wet, as this
causes heat to transfer through the
material more quickly with the risk of
scalding or burning yourself.
up in the tin, causing it to explode. This
could result in injury and scalding or
damage.
Do not use pots and pans on the
~
ceramic hob with bases with
Do not flambé under a cooker hood. pronounced edges or or ridges, e.g.
~
The flames could set the cooker hood
on fire.
cast iron pans. These could scratch or
scour the hob surface permanently.
Do not use the appliance as a
~
resting place for anything else. Take
Never heat an empty pan unless the
~
manufacturer of the pan expressly
particular care never to place cutlery or states that you can do so. Because
other metal objects on the appliance.
When the appliance is switched on
either deliberately or by mistake, or
when there is residual heat present,
there is the risk of metal objects heating
up, with a danger of burning.
Depending on the material, other
objects left on the hob could also melt
or catch fire.
induction heating works extremely
quickly the base of the pan could heat
up to the temperature at which oil or fat
self-ignites within a very short time.
Keep the hob clean. Grains of salt,
~
sugar and sand (e.g. from cleaning
vegetables) can cause scratches.
Never place hot pans on the area
~
around the controls. This could damage
Damp pan lids might adhere to the
ceramic surface and be difficult to
dislodge.
the electronic unit underneath.
Do not drop anything on the ceramic
~
surface. Even a light object could
Switch the cooking zones off after use.
Do not cover the appliance, e.g.
cause damage in certain
~
with a cloth, kitchen foil, etc. This could circumstances.
be a fire hazard if the appliance is
switched on by mistake.
Do not use plastic or aluminium foil
~
containers. These melt at high
temperatures, and could catch fire.
24
Warning and safety instructions
Do not allow either solid or liquid
Metal utensils stored in a drawer
~
~
sugar, or pieces of plastic or aluminium under the hob can become hot if the
foil to get onto the cooking zones when induction hob is used intensively for a
they are hot. If this should occur, switch long time.
off the appliance, and carefully scrape
Always ensure that food is
~
sufficiently cooked or reheated.
off all the sugar, plastic or aluminium
residues from the hob whilst they are
still hot, using a shielded scaper blade.
Take care not to burn yourself.
If residues are allowed to cool before
being removed, the ceramic surface
will be susceptible to pitting or even
cracking.
Some foods may contain
micro-organisms which are only
destroyed by thorough cooking at a
sufficiently high temperature for long
enough. Therefore, when cooking or
reheating food such as poultry, it is
particularly important that the food is
completely cooked through. If in doubt,
select a longer cooking or reheating
time.
Once the residues have been removed,
allow the appliance to cool down, and
then clean with a suitable proprietary
ceramic hob cleaner.
If the hob is built in over a pyrolitic
~
When using an electric socket near
~
oven, the hob should not be used whilst
the pyrolitic process is being carried
out, as this could trigger the
the hob, care should be taken that the
cable of the electrical appliance does
not come into contact with a hot
overheating protection mechanism on
the hob (see relevant section).
cooking zone. The insulation on the
cable could become damaged, giving
rise to an electric shock hazard.
This appliance is fitted with a
~
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
cooling fan. If a drawer is fitted directly
underneath the hob, ensure that there
is sufficient space between the drawer
and its contents and the underside of
the appliance in order to ensure
sufficient ventilation for the hob. Do not
store pointed or small items or paper in
the drawer. They could get in through
the ventilation slots or be sucked into
the housing by the fan and damage the
fan or impair cooling.
Spray canisters, aerosols and other
~
inflammable substances must not be
stored in a drawer under the hob.
Cutlery inserts must be heat-resistant.
25
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and can normally be
recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Please dispose of it at your local
community waste collection/recycling
centre or contact you dealer for advice.
Ensure that it presents no danger to
children while being stored for
disposal.
It should be unplugged or
disconnected from the mains electricity
supply by a competent person.
26
Before using for the first time
Please stick the extra data plate for the Before using for the first time
appliance supplied with this
On hobs with bevelled glass edges,
a small gap may be visible between
the hob and the worktop during the
first few days after installation. This
gap will reduce with time as the
appliance is used and will not affect
the electrical safety of your
documentation in the space provided in
the "After sales service, data plate"
section of this booklet.
Cleaning for the first time
Remove any protective wrapping and
adhesive labels.
appliance.
Before using for the first time, clean the
appliance with a damp cloth only and
then wipe dry.
When the appliance is used for the first
time, it may give off a slight smell. The
smell and any vapours will dissipate
after a short time. They are not harmful
and do not indicate a faulty connection
or appliance.
Do not use washing-up liquid to
clean the ceramic surface as it can
leave a blue sheen which may be
difficult to remove.
27
Induction
The induction principle
If a suitable pan is placed on the
cooking zone within 3 minutes, the ß
will go out and you can continue as
normal.
An induction coil is located under each
cooking zone. When a cooking zone is
switched on, this coil creates a
magnetic field which impacts directly
on the base of the pan and heats it up.
The cooking zone itself is heated up
indirectly by the heat given off by the
pan.
If no pan or an unsuitable pan is placed
on the cooking zone, the cooking zone
and the hob will switch off automatically
after 3 minutes.
Take particular care never to place
cutlery or other metal objects on the
hob. When the appliance is
switched on either deliberately or by
mistake, or when there is residual
heat present, there is the risk of
metal items heating up with the
danger of burning.
An induction cooking zone only works
when a ferromagnetic pan is placed on
it (see "Pans").
Induction automatically recognises the
size of the pan, i.e. heat is only
generated in the area covered by the
base of the pan.
Switch the cooking zones off after
use.
The cooking zone will not work:
– if it is switched on without a pan in
place, or if the pan is unsuitable
(non-magnetic base).
– if the diameter of the base of the pan
is too small.
– if the pan is taken off the cooking
zone when it is switched on.
If this happens, ß will flash in the
relevant cooking zone display
alternating with 0 or the power setting
selected .
28
Induction
Noises
The appliance has a cooling fan to help
extend the life of the electronics. When
the hob is being used intensively, this
will come on and you will hear a
whirring sound. The fan may continue
to run after the appliance has been
switched off.
When using an induction cooking zone,
the following noises can occur in the
pan, depending on what it is made of
and how it has been constructed.
– On the higher power settings, it
might buzz. This will decrease or
cease altogether when the power
setting is reduced.
– If the pan base is made of layers of
different materials (e.g. in a
sandwiched base), it might emit a
cracking sound.
– Whistling might occur if linked zones
(see "Booster function") are being
used at the same time, and the pans
also have bases made of layers of
different materials.
– You might hear a clicking sound from
the electronic switches, especially on
lower settings.
29
Induction
Pans
Pan size
To make optimum use of the cooking
zones, choose pans with base
Suitable pans include:
– stainless steel pans with a magnetic
base
diameters larger than the innermost
markings but smaller than the
outermost markings. If the base
diameter of the pan is smaller than the
innermost marking, the induction
heating will not work. The zone will
behave as if it had no pan on it.
– enamelled steel pans
– cast iron pans
Unsuitable pans:
– stainless steel pans without a
magnetic base
Please note that the maximum diameter
quoted by manufacturers often refers to
the diameter of the top rim of the pot or
pan. The diameter of the base
– aluminium and copper pans
– glass, ceramic or earthenware pots
and pans
(generally smaller) is more important.
To test whether a pot or pan is suitable
for use on an induction hob, hold a
magnet to the base of the pan. If the
magnet sticks, the pan is suitable.
Tips on saving energy
Use a lid whenever possible to
minimise heat loss.
Please be aware that the properties of
the pan base can affect the eveness
with which food heats up in the pan.
Uncovered
Covered
30
Use
Sensor switches
Switching on
This hob is equipped with electronic
sensor switches which react to finger
contact.
The hob must be switched on before
any of the zones can be used.
Do not leave the appliance
To operate a cooking zone, touch the
relevant sensor. Each time you touch a
sensor switch, an audible tone sounds.
unattended whilst it is being used.
To switch the hob on
^ Touch the ON/OFF sensor s.
0 appears in each of the cooking zone
displays. If no further entry is made, the
hob will switch itself off after a few
seconds for safety reasons.
To switch a cooking zone on
^ Select a power setting between 1 and
9 or the keeping warm function by
touching the - or + sensor.
To select cooking with Auto heat-up,
press the - sensor first (see "Auto
heat-up"). To select cooking without
Auto heat-up, press the + sensor first.
Take care only to touch the middle
of the sensor required. Keep the
control panel clean, and do not
place anything on top of it. The
sensors may fail to react or they
could mistake the article or any dirt
for a fingertip contact, thereby
activating a function or even causing
the hob to switch off automatically
(see Safety switch-off.)
If you wish to switch on another
cooking zone, and the 0 for that zone
has already gone out, simply press the
- or + briefly. The 0 will reappear and
you can select a power setting (with or
without Auto heat-up).
Never place hot pans on the sensor
switches. The electronic unit
underneath could get damaged.
31
Use
Settings
Settings*
Standard
Extended
settings**
factory settings
(9 settings)
(17 settings)
Keeping warm
h
h
Melting butter
1 - 2
1 - 2.
Dissolving gelatine
Warming small quantities of liquid
Cooking rice
3
4
3 - 3.
4 - 4.
Defrosting frozen vegetables
Warming liquid and semi-solid foods
Thickening sauces, e.g. Hollandaise
Making porridge
Preparing omelettes, lightly fried eggs
Steaming fruit
Defrosting deep frozen food
Steaming vegetables, fish
Cooking broths, pulse soups
5
5
Bringing large quantities of food to the boil
Cooking dumplings
6
7
5. - 6
Gentle braising (without overheating the fat) of meat, fish,
vegetables, fried eggs
6. - 7.
Frying pancakes etc.
8
9
8 - 8.
9
Boiling large quantities of water
Bringing to the boil
*
These settings, which envisage approx. 4 servings, should only be taken as a guide. With deep
pans, larger quantities or when cooking without a lid, a higher setting is required. For smaller
quantities, select a lower setting.
** If you wish to fine-tune a setting, you can extend the power setting range (see "Programming").
The intermediate setting will be represented by an illuminated dot next to the number.
32
Use
Auto heat-up
When Auto heat-up has been activated,
the cooking zone switches on
Continued
Heat-up time
automatically at the highest setting and
then switches to the continued cooking
setting which you have previously
selected. The heat-up time depends on
which continued cooking setting has
been chosen (see chart).
cooking setting* in minutes and
seconds
(approx.)
1
1.
2
0 : 15
0 : 15
0 : 15
0 : 15
0 : 25
0 : 25
0 : 50
0 : 50
2 : 00
5 : 50
5 : 50
2 : 50
2 : 50
2 : 50
2 : 50
2 : 50
-
Taking a pan off the zone whilst Auto
heat-up is in operation interrupts the
Auto heat-up. It will resume if a pan is
placed back on the zone within 3
minutes.
2.
3
3.
4
To activate Auto heat-up
^ Press the - sensor until the required
continued cooking setting appears,
e.g. 6.
4.
5
5.
6
6.
7
During the heat-up time an indicator
lamp to the right of the continued
cooking setting will light up, and go out
at the end of it.
7.
8
8.
9
At any point during the Auto heat-up
time you can use - or + to lower or
increase the continued cooking setting.
The Auto heat-up time will alter
accordingly.
* The continued cooking settings with
a dot after the number are only
available if the power level range has
been extended (see "Programming").
In the extended range of settings (see
"Programming - P2"), A flashes
alternately with the continued cooking
setting until the heat-up time has
finished.
33
Use
Booster function
The extra boost of energy is only
available by taking a proportion of
energy away from another cooking
zone. For this reason, the cooking
zones are networked in pairs as shown.
The cooking zones are equipped with
Single (l) or Twin Boosters (I/II) (see
"Guide to the appliance").
When activated, the power is boosted
so that large quantities can be heated
quickly, e.g. boiling water for cooking
pasta. When Booster l is activated, the
cooking zones will operate with extra
power for 10 minutes and when Booster
II is activated with extra power for 15
minutes.
When the booster is switched on, the
following happens:
– if Auto heat-up is activated on either
zone in the same network, this will be
switched off.
The Booster function can only be used
on two cooking zones at the same time,
one on the left and one on the right.
– the power level on the other linked
cooking zone will sometimes
decrease.
If the Booster function is switched on
when
– no setting has been selected, the
cooking zone will revert automatically
to setting 9 at the end of the Booster
time or if the Booster function is
switched off before this.
When Booster II is switched on, the
linked cooking zone is switched off.
– a setting has been selected, the
cooking zone will revert automatically
to the setting selected at the end of
the Booster time or if the Booster
function is switched off before this.
Taking a pan off the zone whilst the
Booster is in operation interrupts the
Booster function. It will resume if a pan
is placed back on the zone within 3
minutes.
34
Use
To activate Booster l
To deactivate the booster function
^ If necessary, switch on the required
The booster function can be cancelled
early.
cooking zone.
^ Touch the B sensor for the relevant
^ Touch the B sensor for the relevant
cooking zone repeatedly until the
indicator lamp for the Booster
function goes out in the display, and
a setting appears instead; or touch
the - sensor for the relevant cooking
zone.
cooking zone.
I will show in the cooking zone display,
and the indicator lamp for the Booster
function will also light up.
To activate Booster II
^ If necessary, switch on the required
cooking zone.
^ Touch the B sensor for the relevant
cooking zone.
I will show in the cooking zone display,
and the indicator lamp for the Booster
function will also light up.
^ Touch the B sensor again for the
relevant cooking zone.
II will appear in the display for the
cooking zone.
35
Use
Keeping warm
Useful tips
Each cooking zone has a keeping
warm function.
Only use pans for keeping food warm.
Cover the pan with a lid.
If the keeping warm function has been
activated, the cooking zone will switch
off automatically after a maximum of 2
hours.
You do not have to stir food while it is
being kept warm.
Nutrients are lost when food is cooked,
and continue to diminish when food is
kept warm. The longer food is kept
warm for, the greater the loss of
This function is for keeping food that
has just been cooked warm, i.e.
food that is still hot. It is not for
reheating food that has gone cold.
nutrients. Try to ensure that food is kept
warm for as short a time as possible.
36
Use
Switching off and residual heat The lines of the residual heat indicator
go out one after another as the cooking
zones cool down. The last horizontal
line only goes out when the cooking
zone is safe to touch.
indicators
Switching off a cooking zone
^ Touch the - and + sensors for the
zone you want to switch off at the
same time.
The residual heat indicators also
react to hot dishes and plates being
placed on a cooking zone that is not
switched on.
A 0 will light up in the display for that
zone for a few seconds. If the cooking
zone is still hot, residual heat will then
be indicated in the display.
Do not touch any zone or place any
heat sensitive items on a zone where
the residual heat indicators are lit
up.
Please note that the residual heat
indicators do not light up if there is a
fault message, even if the cooking
zones are still hot.
Switching off the hob
^ Touch the ON/OFF sensor s.
This switches off all cooking zones. The
residual heat indicator will appear in the
display of any cooking zone which is
still hot.
37
Timer
The timer can be used for two different
functions:
Minute minder
To set the minute minder time
– To set the minute minder
The minute minder can be used with
the hob switched on or off.
– To set a cooking zone to switch off
automatically.
You can select a time from 1 minute
(01) to 91/2 hours (9.^). If a time of more
than 99 minutes (99) is set, the time is
set in half-hour steps. The half hour is
indicated by a dot after the number.
^ Touch the m, - or + sensor.
00 appears in the timer display, and the
minute minder indicator lamp will flash.
^ Whilst the indicator light is flashing,
touch the - or + sensor until the time
you require appears in the display,
e.g. 15 minutes.
Use the - sensor to reduce the time
from 9.^ to 00, and the + sensor to
increase the time from 00 to 9.^. The
display stops at 2h and at 99. To
continue entering the setting, briefly
remove your finger from the sensor,
and then touch it again.
When the set time has elapsed, 00 will
appear in the timer display for a few
seconds. An audible tone will sound at
the same time. To turn the audible tone
off before it has finished, touch the m
sensor.
The time then counts down in minutes.
The time remaining can be seen in the
display and changed at any time by
touching - or +.
To delete the minute minder time
^ Touch the - and + sensors at the
same time.
38
Timer
To switch a cooking zone off
automatically
^ Touch the - or + sensor until the time
you require appears in the display,
e.g. 15 minutes.
It is only possible to programme a
cooking zone to switch off automatically
if a power setting has already been
selected for that zone. All of the
cooking zones can be programmed at
the same time.
The time then counts down in minutes.
The time remaining can be seen in the
display and changed at any time by
touching - or +.
If the time programmed is longer than
the maximum operational time
allowed, the cooking zone will switch
off after the maximum time allowed
(see relevant section).
If you want to set another cooking zone
to switch off automatically, follow the
same steps as described above.
If more than one switch-off time is
programmed, the shortest time
^ Select a power setting for the zone
you require, e.g. back right, in the
usual way.
remaining will show in the display, and
the indicator lamp for that particular
cooking zone will flash. All the other
indicator lamps will light up constantly.
If you want to check on the remaining
time for another zone, touch the m
sensor until the indicator lamp for the
zone you require flashes.
^ Touch the m sensor.
00 appears in the timer display, and the
minute minder indicator lamp will flash.
^ Touch the m sensor again.
The indicator lamp for the minute
minder in the timer display goes out,
and an indicator lamp for automatic
switch-off of a cooking zone flashes.
^ If several cooking zones are being
used, touch the m sensor repeatedly
until the indicator lamp flashes next
to the cooking zone you wish to use
this function for, e.g. back right.
The indicator lamps for the cooking
zones being used light up clockwise,
starting with the front left.
39
Timer
To use both timer functions at
the same time
The minute minder and automatic
switch-off functions can be used at the
same time.
If you have programmed in one or more
switch-off times, and would like to use
the minute minder as well:
Touch the m sensor repeatedly until
the minute minder indicator lamp
flashes.
If you are using the minute minder, and
would like to programme in one or more
switch-off times as well:
Touch the m sensor repeatedly until
the indicator lamp flashes for the
cooking zone required.
Shortly after the last entry, the shortest
remaining time will come up in the
display. If you want to check on the
remaining time for another zone, touch
the m sensor until the indicator lamp
for the zone you require flashes.
Starting with the shortest remaining
time which is showing in the display, all
cooking zones that are in use and the
minute minder are selected clockwise.
40
Safety features
Safety lock/System lock
To activate the locks
Keep children away from the hob for
their own safety.
^ Touch the $ sensor until the relevant
indicator lamp comes on.
The indicator lamp will go out after a
short while.
Your appliance is equipped with a
safety lock to prevent the hob and the
cooking zones being switched on or
any settings being altered.
You can alter the setting from
one-finger to three-finger operation (see
"Programming") to make it harder for
children to operate the appliance.
The safety lock is activated when the
hob is switched on. If the safety lock is
activated:
To deactivate the locks
– The settings for the cooking zones
and the timer settings cannot be
changed.
^ Touch the $ sensor until the indicator
lamp goes out.
– The cooking zones and hob can be
switched off, but once switched off
cannot be switched on again.
The system lock is activated when the
hob is switched off. If the system lock is
activated, the hob cannot be switched
on and the timer cannot be used.
The hob is programmed in such a way
that the system lock has to be operated
manually. The settings can be changed
so that the system lock is activated
automatically five minutes after the hob
has been switched off (see
"Programming").
If a sensor switched is touched when
the safety lock or the system lock is
activated, the indicator lamp comes on.
The safety lock and the system lock
are deactivated in the case of a
power cut.
41
Safety features
Stop and Go
To activate Stop and Go
Your appliance has a Stop and Go
feature which, when activated, reduces
the power of all switched-on cooking
zones to setting 1. When Stop and Go is
deactivated, the cooking zones resume
at the power level which was last set.
If Stop and Go is not deactivated, the
hob switches off after 1 hour.
^ Touch the $ sensor until you hear
two consecutive beeps.
Be careful not to continue touching
the $ sensor for too long, as this will
activate the safety lock.
The indicator lamp for the safety lock
will start to flash. The power of the
cooking zones in use will be reduced to
setting 1, and a 1 will appear in the
corresponding cooking zone displays.
If you wish to use this feature, you will
need to alter the factory setting (see
"Programming").
To deactivate Stop and Go
If automatic switch-off is programmed
for a cooking zone, activating Stop and ^ Touch the $ sensor until the indicator
Go will interrupt the count down to the
switch-off time. When Stop and Go is
deactivated, the automatic switch-off
programme time will continue to run
without further interruption.
lamp goes out.
The cooking zones will now run at the
level that was previously set.
If a minute minder time has been set,
this will continue running and will not be
affected by Stop and Go.
42
Safety features
Safety switch-off
Safety switch-off if the sensors are
covered
Your hob is fitted with a safety
switch-off feature in case you forget to
switch it off yourself.
Your hob will switch off automatically if
one or several of the sensors remain
covered for longer than 10 seconds, for
example, by finger contact, food boiling
over or by an object such as an oven
glove or tea towel.
Safety switch-off with an over-long
cooking time
If one of the cooking zones is heated
for an unusually long period of time
(see chart), and the power settings are
not altered, the hob will switch itself off
automatically and the appropriate
residual heat indicator will appear.
An audible tone will sound every 30
seconds (for a maximum of ten
minutes) and an F will flash in the
display for the sensor switch which is
covered.
To use the cooking zone again, switch
it back on in the usual way.
Power setting*
Maximum
operating time
in hours
^ Clean the control area or remove the
obstruction.
This will turn off the tone and the F will
h
2
10
5
go out.
1 / 1.
2 / 2.
3 / 3.
4 / 4.
5 / 5.
6 / 6.
7 / 7.
8 / 8.
9
^ Switch the hob back on again with
the ON/OFF sensor s. The cooking
zones can now be used again as
normal.
5
4
3
2
2
2
1
* The continued cooking settings with
a dot after the number are only
available if the power level has been
increased (see "Programming").
43
Safety features
Overheating protection
Overheating can be caused by:
– Heating up an empty pan
All the induction coils and the cooling
elements for the electronics are fitted
with an overheating protection
– Fats or oils being heated up on the
highest power setting.
mechanism. To prevent the induction
coils and cooling elements from
overheating, the overheating protection
mechanism works on the affected
cooking zone or on the entire hob in the
following ways:
– There being insufficient ventilation to
the underside of the appliance.
If the overheating protection
mechanism triggers again, contact the
Service department.
– If the Booster function is being used,
this will be switched off.
– The power level will be reduced.
– If an induction coil is affected, the
error message FE99 appears and the
hob switches itself off.
The error message will go out, and the
residual heat indicator will appear in the
display of any cooking zone which is
still hot.
The hob can only be used again when
the induction coil has cooled down
sufficiently.
– If a cooling element is affected, the
power supply to the cooking zones
will be reduced, and the set power
level will continue to be displayed.
As soon as the cooling element has
cooled down sufficiently, the cooking
zones will automatically continue to
operate at the original power setting.
44
Cleaning and care
To avoid damaging the outer
,Do not use a steam cleaning
appliance to clean this appliance.
The steam could reach the electrical
components and cause a short
circuit.
surfaces of your appliance, do not
use:
– cleaning agents containing soda,
alkalines, ammonia, acids or
chlorides,
The appliance should be cleaned
regularly, preferably after each use.
Allow it cool down to room temperature
before cleaning.
– cleaning agents containing
descaling agents,
– stain or rust removers,
To avoid water marks and limescale
deposits, use a soft cloth to dry
surfaces that have been cleaned with
water.
– abrasive cleaning agents, e.g.
powder cleaners and cream
cleaners,
– solvent-based cleaning agents,
– dishwasher cleaner,
– grill and oven cleaners,
– glass cleaning agents,
– hard, abrasive brushes or sponges,
e.g. pot scourers, brushes or
sponges which have been previously
used with abrasive cleaning agents,
– sharp, pointed objects which could
damage the seal between the
ceramic surface and the surrounding
frame, and between the frame and
the worktop.
45
Cleaning and care
Ceramic surface
Spots caused by limescale, water and
aluminium residues (spots with a
metalic appearance) can be removed
using the ceramic and stainless steel
hob cleaner.
Wipe all coarse soiling off using a
damp cloth. Stubborn soiling may need
to be removed with a shielded scraper
blade.
Should any sugar, plastic or
Then clean the hob with a suitable
proprietary ceramic and stainless steel
hob cleaner (see "Optional
aluminium foil spill or fall onto a hot
cooking zone while it is in use, first
switch off the appliance. Then carefully
scrape off all the sugar, plastic or
aluminium residues from the hob whilst
they are still hot, using a shielded
scraper blade. Take care not to burn
yourself.
accessories") applied with kitchen
paper or a clean cloth. Do not apply
cleaner whilst the hob is still hot, as this
could result in marking. Please follow
the manufacturer's instructions.
Finally, wipe the hob with a damp cloth, Allow the appliance to cool down, and
then polish with a soft, dry cloth. Ensure then clean as described above with a
that all cleaner residues are removed.
Residues can burn onto the appliance
the next time it is used, and cause
damage to the ceramic surface.
suitable proprietary ceramic and
stainless steel hob cleaner.
46
Programming
You can change the default settings of
the programme options (see chart).
To store the new settings in memory,
touch the hob ON/OFF sensor s until
the displays go out.
^ With the hob switched off, touch the
hob ON/OFF sensor s and the safety
lock sensor $ at the same time until
the indicator lamp for the safety lock
flashes.
If you do not wish to store the settings
in memory, touch the safety lock sensor
$ until the displays go out.
A P (Programme) and an S (Status) will
appear in the cooking zone display with
a number which shows the current
setting (see chart).
^ First select the programme you want
by touching the + or - sensor for the
front left cooking zone, then select
the required status by touching the +
or - sensor for the front right cooking
zone (see chart). You can alter
several programmes one after the
other in this manner.
47
Programming
Programme*
Status** Setting
P
0
Demonstration mode and
factory default settings
S
S
S
S
S
S
0
1
9
0
1
0
Demonstration mode on
Demonstration mode off
Factory default settings reinstated
P
P
1
2
Stop and Go
Off
On
Power setting range
9 power settings
(1, 2, 3 ... to 9)
S
1
17 power settings
(1, 1., 2, 2., 3 ... to 9)
If the Auto heat-up setting is
selected, an A will flash
alternately with the continued
cooking setting in the display.
P
P
P
3
4
5
Induction warning tone
when there is no pan or
the pan is unsuitable
S
S
S
S
S
S
S
S
S
S
0
1
2
3
0
1
2
3
0
1
Off
Quiet
Medium
Loud
Off
Keypad tone when a
sensor is touched
Quiet
Medium
Loud
Off
Audible tone for the Timer
Quiet audible tone on for 10
seconds
S
2
Medium pitched audible tone on
for 10 seconds
S
3
Loud audible tone on for 10
seconds
*
Programmes/Statuses not shown here have no allocation.
** The factory default settings are shown in bold.
48
Programming
Programme*
P
Status** Setting
6
7
8
Safety lock
System lock
Auto heat-up
S
0
One-finger locking using $
S
1
Three-finger locking using $ and
+ on the two right-hand cooking
zones
P
S
0
Activating the system lock
manually
S
1
Activating the system lock
automatically
P
P
S
S
S
S
S
0
1
0
1
2
Off
On
0. Miele|home
Feature not fitted
Signed off
Signed on
- only on
communication-enabled
appliances fitted with a
communication module.
§
Signed on/off working (indicator
light)
P
6. Sensor switch reaction
S
S
S
0
1
2
Slow
speed
Normal (300 ms)
Rapid
* Programmes not shown here have no allocation.
** The factory default settings are shown in bold.
49
Problem solving guide
... there is a strange smell or vapours
when a new appliance is being used.
,Installation work and repairs to
electrical appliances must only be
carried out by a suitably qualified
and competent person in strict
accordance with current local and
national safety regulations (BS 7671
in the UK). Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
The smell and any vapours given off do
not indicate a faulty connection or
appliance, and neither are they
hazardous to health.
... the hob can be switched on and
settings selected, but the cooking
zones do not heat up
unauthorised work.
Ensure that current is not supplied to
the appliance until after
Check whether you set the demo-mode
setting by mistake (see "Programming -
P0").
maintenance or repair work has
been carried out.
What to do if...
... ß appears in the display for a
cooking zone.
... the hob or cooking zones cannot
be switched on
Check whether
Check whether
– the zone was switched on by mistake
without a pan on it.
– the pans being used are suitable.
– the pan being used is suitable for
use on an induction zone, and that it
is large enough (see "Pans").
– the safety lock is activated.
If necessary, deactivate it (see
"Safety lock").
– the mains fuse has tripped.
If none of the above is the case, then
disconnect the appliance from the
electricity supply for approx. 1 minute.
To do this:
... an individual cooking zone or the
whole hob has switched itself off
automatically
The safety switch-off feature or the
overheating protection mechanism has
been triggered (see "Safety switch-off"
and "Overheating protection").
– switch off at the wall socket, or
switch off at the isolator, or
– disconnect the mains fuse.
Reset the trip switch in the mains fuse
box, and switch the appliance back on.
If it still will not switch on, contact a
qualified electrician or the Miele Service
Department.
50
Problem solving guide
... one of the following has occurred:
... The cooling fan continues to run
after the appliance has been
switched off.
– The Booster has deactivated early
automatically.
This is not a fault. The fan will continue
running until the appliance has cooled
down. It will then switch itself off
automatically.
– The power level has been reduced.
– The cooking zone is not working in
the usual way at the power level set.
The overheating protection mechanism
has been triggered (see "Overheating
protection").
... an F appears in the display for the
rear cooking zones, an E appears in
the display for the front cooking
zones and numbers appear in the
timer display.
... the food in the pan hardly heats up
or does not heat up at all when the
Auto heat-up function is switched on
FE99:
The overheating protection mechanism
for the induction coil has been
triggered. The cooking zone can be
used again as soon as it has cooled
down to a safe level.
This could be because:
– there is too much food in the pan.
– the pan is not conducting heat
properly.
With other fault messages:
Interrupt the power supply to the hob
for approx. 1 minute.
Select a higher continued cooking
setting next time, or start cooking at the
highest setting and then turn down to a
lower setting manually later on.
If the problem persists after
reconnecting the appliance to the
power supply, please contact the Miele
Service department.
51
Optional accessories
Miele appliances are designed to give the best possible
results and years of satisfaction. To help you get the most
from your appliance, Miele has put together a
comprehensive range of accessories and cleaning products.
These can be ordered via the internet at:
or from Miele (see back cover for contact details) or from your
Miele dealer.
Miele|home system
Miele|home enabled appliances use the existing household
power supply (Powerline technology) to transfer data to the
Miele|home master appliance (SuperVision appliance with
the InfoControl unit). You can use the master appliance to call
up information about Miele|home appliances, such as the
operational status or fault messages at any time.
The Miele| system allows certain hobs to be linked to certain
cooker hoods (Con{ctivity).
The cooker hood responds automatically to the hob setting,
controlling the power level and lighting accordingly.
To enjoy the benefits of this feature, your appliance will have
to be fitted with a communication module.
XKM 2000 KM
InfoControl
Communication module, including building-in kit
Master appliance with base station and mobile receiver.
52
Safety instructions for installation
After installing the hob, ensure that
~
Fit wall units and extractor hood
the connection cable cannot come into
contact with the underside of the
appliance. Make sure that there is no
mechanical obstruction, such as a
drawer, which could damage it.
before fitting the hob to avoid
damaging the surface.
The veneer or laminate coatings of
~
worktops (or adjacent kitchen units)
must be treated with 100 °C
heat-resistant adhesive which will not
dissolve or distort.
Observe carefully the safety
~
distances given on the following pages.
Do not use any sealant except
~
Any backmoulds must be of
heat-resistant material.
where expressly instructed to do so.
The seal underneath the appliance
provides a sufficient seal for the
This equipment may only be used in
~
worktop (See "General installation tips").
mobile installations such as ships,
caravans, aircraft etc. if a risk
assessment has been carried out by a
suitably qualified engineer.
All dimensions in this instruction booklet
are given in mm.
The hob may not be built in over a
~
fridge, fridge-freezer, freezer,
dishwasher, washing machine or
tumble dryer.
These hobs must not be installed
~
above ovens or cookers unless these
have a built-in cooling down fan.
53
Safety instructions for installation
Safety distance above the appliance
When two or more appliances are
installed together below a cooker hood,
e.g. a gas wok and a ceramic hob,
which have different safety distances
given in the installation instructions, you
should select the greater distance of
the two.
A minimum safety distance must be
maintained between the appliance and
the cooker hood above it. See the
cooker hood manufacturer's operating
and installation instructions for details.
If the manufacturer's instructions are
not available for the cooker hood, a
minimum safety distance of at least
760 mm must be maintained. For any
flammable objects, e.g. utensil rails,
wall units etc. a minimum distance of at
least 760 mm must be maintained
between them and the appliance
below.
54
Safety instructions for installation
Safety distances to the sides and
back of the hob
Ideally the hob should be installed with
plenty of space on either side. There
may be a wall at the rear and a tall unit
or wall at one side. On the other side,
however, no unit or divider should stan-
d higher than the hob (see illustrations).
Not allowed
The following minimum distances
should be adhered to for safety
reasons:
– 50 mm to the right or left of the
worktop cut-out to the nearest piece
of furniture (e.g. tall unit).
– 50 mm from the worktop cut-out to
the rear wall.
Recommended
Not recommended
55
Safety instructions for installation
Safety distances underneath the hob
To ensure sufficient ventilation to the
hob, a certain gap must be left between
the underside of the hob and any oven,
interim shelf or drawer.
The minimum gap between the
underside of the hob and
– the top of an oven is 15 mm.
– the top of an interim shelf is 15 mm.
A space of at least 10 mm must also
be left at the back to accommodate
the cable.
– the base of a drawer must be
75 mm.
56
Safety instructions for installation
Safety distance when installing the appliance near a wall with additional
niche cladding
There must be a minimum distance of 50 mm between the niche cladding and the
worktop cut-out.
This distance is only necessary for niche cladding made of wood or any other
combustible material. For non-combustible materials (metal, ceramic tiles or
similar), this dimension can be reduced by the thickness of the niche cladding
material. The materials can warp or distort when subjected to high temperatures.
Flush-fitted hobs
Hob with frame or bevelled edge
aMasonry
bNiche cladding
cBackmould
dWorktop
eWorktop cut-out
fMinimum distance of 50 mm
57
Hob with frame or bevelled edge
Building-in dimensions
KM 5941
514
614
44
8
b
30
0
R4
ß
0
50
500
1
+
+
1
-
-
600
a
c
b
205
250
a
53
44
d
aFront
bBuilding-in depth
cBuilding-in depth, including mains connection cable
dMains connection cable, L = 1440 mm
58
Hob with frame or bevelled edge
KM 5942
504
574
50
48
3
b
30
0
0
ß
R4
+3
490
+3
560
a
b
a
209
48
422
250
475
c
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
59
Hob with frame or bevelled edge
KM 5943
46,5
510
4
670
b
30
0
ß
R4
0
50
a
b
a
209
46,5
422
245
475
c
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
60
Hob with frame or bevelled edge
KM 5945
514
614
50
48
3
b
30
0
0
ß
R4
+3
500
+3
600
a
b
209
a
48
422
230
475
c
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
61
Hob with frame or bevelled edge
KM 5946
504
574
48
3
b
30
0
0
ß
R4
50
+3
490
+3
560
a
b
a
222
48
422
237
475
c
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
62
Hob with frame or bevelled edge
KM 5947
504
574
50
44
8
b
30
0
R4
ß
0
490
1
+
+
-
1
-
560
a
c
b
209
250
a
53
44
d
aFront
bBuilding-in depth
cBuilding-in depth, including mains connection cable
dMains connection cable, L = 1440 mm
63
Hob with frame or bevelled edge
KM 5951
504
3
48
764
b
30
0
ß R4
0
50
490 +3
3
+
750
a
d
b
b
85
32
15
4
a
b
48
209
422
15
250
328
225
c
149
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
dConnection for Miele|home
64
Hob with frame or bevelled edge
KM 5952
510
4
860
48
b
ß
30
ß R4
0
50
+ 3
490 +
3
750
a
b
b
209
a
13
48
b
422
13
125
250
475
c
149
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
65
Hob with frame or bevelled edge
KM 5954
514
8
44
794
b
30
0
R4
ß
0
50
1
+
-
500
+
1
-
780
a
c
b
209
a
53
44
250
d
aFront
bBuilding-in depth
cBuilding-in depth, including mains connection cable
dMains connection cable, L = 1440 mm
66
Hob with frame or bevelled edge
KM 5955
504
3
48
764
50
b
30
0
ß R4
0
490 +3
3
+
750
a
d
b
b
65
32
15
24
a
b
48
209
422
15
250
328
225
c
149
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
dConnection for Miele|home
67
Hob with frame or bevelled edge
KM 5957
514
3
48
794
b
30
0
ß R4
0
50
500 +
3
+
3
780
a
b
d
b
69
20
15
32
a
c
b
48
209
15
62
422
250
328
225
164
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
dConnection for Miele|home
68
Hob with frame or bevelled edge
KM 5958
504
3
48
764
50
b
30
0
ß R4
0
490 +
3
+
3
750
a
b
d
b
220
15
a
32
b
48
209
422
15
250
354
225
c
149
aFront
bBuilding-in depth
cMains connection cable, L = 1440 mm
dConnection for Miele|home
69
Hob with frame or bevelled edge
KM 5975
416
47,5
4
916
b
30
0
ß R4
0
50
+3
886
386
+3
a
e
c
52,5 (57,5)
177
a
154
b
56,5
47,5
74
230
74
d
aFront
bBuilding-in depth
cBuilding-in depth, including mains connection cable
dMains connection cable, L = 1440 mm
eConnection for Miele|home
Building-in depth, including Miele|home connection cable = 57,5 mm
70
Hob with frame or bevelled edge
KM 5985
416
47,5
4
916
b
30
0
ß R4
0
50
+3
886
386
+3
a
b
c
a
177
56,5
47,5
74
74
d
aFront
bBuilding-in depth
cBuilding-in depth, including mains connection cable
dMains connection cable, L = 1440 mm
71
Hob with frame or bevelled edge
Installation
Installing the hob
^ Feed the hob connection cable down
Preparing the worktop
through the cut-out.
^ Make the worktop cut-out following
the dimensions applicable.
^ Place the hob centrally in the cut-out.
When doing this make sure that the
seal under the hob sits flush with the
worktop on all sides. This is important
to ensure an effective seal all round.
Do not use sealant.
Remember to maintain a minimum
safety distance from the back wall,
as well as from any tall unit or side
wall to the right or left of the hob.
See "Safety instructions for
^ Connect the hob to the mains.
installation".
^ Check that the hob works.
^ Seal the cut surfaces on
wood/laminated worktops with a
suitable heat-resistant sealant to
avoid swelling caused by moisture.
If, during installation, you find that
the seals on the corners of the frame
are not flush with the worktop, the
corner radius ß R4, can be carefully
scribed to suit.
These hobs have a seal underneath
them to keep the hob securely in
position. Clamps are not required.
Any gap between the frame and
worktop will reduce with time.
72
Hob with frame or bevelled edge
General installation tips
Do not use any sealant unless
expressly instructed to do so. The
sealing strip under the edge of the top
part of the appliance provides a
sufficient seal for the worktop.
Do not use sealant between the
frame of the top part of the
appliance and the worktop.
This could cause difficulties if the
appliance ever needs to be taken
out for servicing and possibly result
in damage to the frame or the
worktop.
73
Flush-fitted hobs
Building-in dimensions
KM 5944 / KM 5948
+
+1
492
1
-
-
592
51
b
30
0
ß
R4
1
0
-
50
470
-
1
570
1
-
496
-
1
596
13
a
d
596-1
570-1
b
475
a
209
51
422
d
250
475
ß
R4
c
aFront
bBuilding-in depth
cMains connection cable,
L = 1440 mm
Cut-out dimensions for granite or
marble worktops.
Please take careful note of the inset
diagram.
dStepped cut-out for granite or marble
worktops
74
Flush-fitted hobs
KM 5956
492+
1
+
-
-
1
51
752
b
30
0
ß R4
0
50
1
-
470
1
-
730
1
496
-
-
1
756
13
a
d
b
b
e
b
24
756-1
730-1
17
209
a
b
51
422
17
115
d
b
24
250
c
475
ß
R4
138
aFront
Cut-out dimensions for granite or
marble worktops.
Please take careful note of the inset
diagram.
bBuilding-in depth
cMains connection cable,
L = 1440 mm
dStepped cut-out for granite or marble
worktops
eConnection for Miele|home
75
Flush-fitted hobs
KM 5953 / KM 5986
492+
1
+
-
-
1
51
752
b
30
0
ß R4
0
50
1
-
470
1
-
730
1
496
-
-
1
756
13
a
d
b
b
b
24
756-1
730-1
17
209
a
b
51
422
17
115
d
b
24
250
c
475
ß
R4
138
aFront
Cut-out dimensions for granite or
marble worktops.
Please take careful note of the inset
diagram.
bBuilding-in depth
cMains connection cable,
L = 1440 mm
dStepped cut-out for granite or marble
worktops
76
Flush-fitted hobs
Installation
The hob can be installed
– in a suitable cut-out in a granite or
marble worktop.
Flush fit hobs are only suitable for
installation in granite, marble, tiled or
solid wood worktops. Other
– in a suitable cut-out in a tiled or solid
wood worktop with a wooden support
frame. The frame must be provided
on site, and is not supplied with the
appliance.
materials such as Corian and
Askilan are not suitable.
This appliance requires a 800 mm
wide base unit for installation.
The hob must be accessible from
below for servicing purposes and to
ensure that the seal around it is not
dislodged.
77
Flush-fitted hobs
Making the worktop cut-out and
building in the hob
^ Make the worktop cut-out as shown
in "Building-in dimensions".
^ Feed the hob connection cable down
Granite and marble worktops
through the cut-out.
^ Centre the hob f in the cut-out.
^ Connect the hob to the mains.
^ Check that the hob works.
^ Seal the remaining gap g with a
silicone sealant that is heat-resistant
to at least 160 °C.
For granite and marble worktops,
only use silicone sealant that is
especially formulated for granite and
marble, and observe the sealant
manufacturer's instructions.
eWorktop
fHob
gGap
Corner radius of the worktop ß R4
As the ceramic glass and the
worktop cut-out have a certain
dimensional tolerance, gap g can
vary (min. 1 mm).
78
Flush-fitted hobs
Solid wood and tiled worktops
^ Make the worktop cut-out as shown
in "Building-in dimensions".
^ Fix the wooden frame a 7 mm
below the top edge of the worktop
(see diagram).
^ Feed the hob connection cable down
through the cut-out.
^ Centre the hob f in the cut-out.
^ Connect the hob to the mains.
^ Check that the hob works.
^ Seal the remaining gap g with a
silicone sealant that is heat-resistant
to at least 160 °C.
aWooden frame 13 mm
(to be provided on site)
Observe the silicone sealant
manufacturer's instructions.
eWorktop
fHob
For granite and marble tiled
worktops, only use silicone sealant
that has been especially formulated
for granite and marble.
gGap
Corner radius of the tiled worktop ß R4
As the ceramic glass and the
worktop cut-out have a certain
dimensional tolerance, gap g can
vary (min. 1 mm).
79
Electrical connection
Connection should be made via a
suitable isolator which complies with
national and local safety regulations,
and the On/Off switch should be easily
accessible after the appliance has
been built in.
All electrical work should be carried
out by a suitably qualified and
competent person, in strict
accordance with current local and
national safety regulations (BS 7671
in the UK).
If the switch is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
For extra safety it is advisable to install
a residual current device (RCD). Please
contact a qualified electrician for
advice.
unauthorised work.
A damaged cable must be replaced
by a suitably qualified electrician
with a special connection cable of
type H 05 VV-F, available from the
Miele Customer Contact Centre.
When switched off there must be an
all-pole contact gap of at least 3 mm in
the isolator switch (including switch,
fuses and relays).
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Important U.K.
The appliance is supplied for
connection to a 230-240 V, 50 Hz
supply with a 3-core cable.
The appliance must only be
operated when built-in. This is to
ensure that all electrical parts are
shielded. Live parts must not be
exposed.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
Blue
= neutral
= live
Brown
Please make sure that the connection
data quoted on the data plate match
the household mains supply.
80
Electrical connection
WARNING
Wiring diagram
THIS APPLIANCE MUST BE
EARTHED
The electrical safety of this appliance
can only be guaranteed when
continuity is complete between it and
an effective earthing system, which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested and where
there is any doubt, the electrical wiring
in the home should be inspected by a
qualified electrician. The manufacturer
cannot be held liable for the
consequences of an inadequate
earthing system such as an electric
shock.
The manufacturer cannot be held
liable for damage which is the direct
or indirect result of incorrect
installation or connection.
N.B. This appliance is supplied
single phase only in the U.K. / AUS /
NZ
81
After sales service, data plate
In the event of any faults which you cannot remedy yourself, or if the appliance is
under guarantee, please contact:
– Your Miele dealer, or
– the Miele Service Department (see back cover for address).
Please note that telephone calls may be monitored and recorded to improve
our service.
When contacting Miele, please quote the model and serial number of your
appliance. which are given on the data plate.
Space in which to stick the extra data plate supplied with the appliance. Ensure
that the model number is the same as the one on the front of these instructions.
82
83
Alteration rights reserved / xx08
M.-Nr. 07 257 390 / 03
|
IBM THINKCENTER 8189 User Manual
Intel IB865 User Manual
IOGear M0560 User Manual
LG Electronics LG Life Good Computer Monitor W2253TQ User Manual
Lucent Technologies 61227A User Manual
Memorex MT3010OM User Manual
NEC 1525M User Manual
Philips 34PT9421 User Manual
Philips DVDR3350H User Manual
Philips MWB1225I User Manual