CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
36-Mbit DDR-II+ SRAM 2-Word
Burst Architecture (2.0 Cycle Read Latency)
Features
Functional Description
■ 36-Mbit density (4M x 8, 4M x 9, 2M x 18, 1M x 36)
■ 300 MHz to 375 MHz clock for high bandwidth
■ 2-Word burst for reducing address bus frequency
The CY7C1246V18, CY7C1257V18, CY7C1248V18, and
CY7C1250V18 are 1.8V Synchronous Pipelined SRAM
equipped with DDR-II+ architecture. The DDR-II+ consists of an
SRAM core with advanced synchronous peripheral circuitry.
Addresses for read and write are latched on alternate rising
edges of the input (K) clock. Write data is registered on the rising
edges of both K and K. Read data is driven on the rising edges
of both K and K. Each address location is associated with two
8-bit words (CY7C1246V18), 9-bit words (CY7C1257V18),
18-bit words (CY7C1248V18), or 36-bit words (CY7C1250V18)
that burst sequentially into or out of the device.
■ Double Data Rate (DDR) interfaces
(data transferred at 750 MHz) at 375 MHz
■ Read latency of 2.0 clock cycles
■ Two input clocks (K and K) for precise DDR timing
❐ SRAM uses rising edges only
Asynchronous inputs include output impedance matching input
■ Echo clocks (CQ and CQ) simplify data capture in high speed
systems
(ZQ). Synchronous data outputs (Q, which share the same
physical pins with the data inputs, D) are tightly matched to the
two output echo clocks CQ/CQ, eliminating the need to capture
data separately from individual DDR SRAMs in the system
design.
■ Data valid pin (QVLD) to indicate valid data on the output
■ Synchronous internally self-timed writes
■ Core V = 1.8V ± 0.1V; IO V
= 1.4V to V
DD
DD
DDQ
All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the K or K input clocks. Writes are
conducted with on-chip synchronous self-timed write circuitry.
■ HSTL inputs and variable drive HSTL output buffers
■ Available in 165-ball FBGA package (15 x 17 x 1.4 mm)
■ Offered in both in Pb-free and non Pb-free packages
■ JTAG 1149.1 compatible test access port
■ Delay Lock Loop (DLL) for accurate data placement
Configurations
With Read Cycle Latency of 2.0 cycles:
CY7C1246V18 – 4M x 8
CY7C1257V18 – 4M x 9
CY7C1248V18 – 2M x 18
CY7C1250V18 – 1M x 36
Selection Guide
Description
Maximum Operating Frequency
Maximum Operating Current
375 MHz
375
333 MHz
333
300 MHz
300
Unit
MHz
mA
1210
1080
1000
Note
1. The QDR consortium specification for V
is 1.5V + 0.1V. The Cypress QDR devices exceed the QDR consortium specification and are capable of supporting
DDQ
V
= 1.4V to V
.
DDQ
DD
Cypress Semiconductor Corporation
Document Number: 001-06348 Rev. *D
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 11, 2008
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Logic Block Diagram (CY7C1248V18)
Write
Reg
Write
Reg
20
A
(19:0)
Address
Register
LD
18
K
K
Output
Logic
Control
CLK
Gen.
R/W
DOFF
Read Data Reg.
36
CQ
CQ
V
18
REF
18
18
Reg.
Reg.
Reg.
Control
Logic
R/W
DQ
[17:0]
18
BWS
18
[1:0]
QVLD
Logic Block Diagram (CY7C1250V18)
Write
Reg
Write
Reg
19
A
(18:0)
Address
Register
LD
36
K
K
Output
Logic
Control
CLK
Gen.
R/W
DOFF
Read Data Reg.
72
36
CQ
CQ
V
REF
36
36
Reg.
Reg.
Reg.
Control
Logic
R/W
DQ
[35:0]
36
BWS
36
[3:0]
QVLD
Document Number: 001-06348 Rev. *D
Page 3 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Pin Configurations
165-Ball FBGA (15 x 17 x 1.4 mm) Pinout
CY7C1246V18 (4M x 8)
1
2
3
A
4
5
NWS1
NC/288M
A
6
K
7
8
9
A
10
A
11
CQ
DQ3
NC
NC/72M
NC/144M
A
B
C
D
CQ
NC
NC
NC
NC
NC
NC
R/W
A
LD
A
NC
NC
NC
NC
NC
NC
K
NC
NC
NC
NC
NC
NC
NWS0
A
VSS
VSS
A
VSS
VSS
VSS
VSS
VSS
NC
NC
NC
DQ4
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
NC
NC
NC
NC
DQ2
E
F
VDD
VDD
VDD
VDD
VDD
VSS
NC
NC
ZQ
NC
DQ5
VDDQ
NC
NC
NC
G
H
J
VREF
NC
VDDQ
NC
VREF
DQ1
NC
DOFF
NC
NC
NC
DQ0
NC
NC
NC
NC
NC
K
L
DQ6
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
VSS
VSS
VSS
A
VSS
A
VSS
A
VSS
VSS
NC
NC
NC
NC
NC
NC
NC
NC
NC
M
N
P
DQ7
A
QVLD
A
A
A
A
A
A
A
TDO
TCK
A
NC
A
TMS
TDI
R
CY7C1257V18 (4M x 9)
1
2
3
A
4
5
NC
6
7
8
9
A
10
A
11
CQ
DQ3
NC
NC/72M
NC/144M
A
B
C
D
CQ
NC
NC
NC
R/W
A
K
K
LD
A
NC
NC
NC
NC
NC
NC
NC/288M
NC
NC
NC
NC
NC
NC
BWS0
A
VSS
VSS
A
A
VSS
VSS
VSS
VSS
VSS
NC
NC
NC
NC
NC
NC
DQ4
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
NC
NC
NC
NC
DQ2
E
F
VDD
VDD
VDD
VDD
VDD
VSS
NC
NC
ZQ
NC
DQ5
VDDQ
NC
NC
NC
G
H
J
VREF
NC
VDDQ
NC
VREF
DQ1
NC
DOFF
NC
NC
NC
DQ0
NC
NC
NC
NC
NC
NC
NC
NC
K
L
DQ6
NC
NC
NC
NC
NC
NC
NC
NC
VSS
VSS
VSS
A
VSS
A
VSS
A
VSS
VSS
NC
NC
NC
NC
NC
NC
NC
NC
M
N
P
DQ7
A
QVLD
A
DQ8
A
A
A
A
A
A
TDO
TCK
A
A
TMS
TDI
R
NC
Document Number: 001-06348 Rev. *D
Page 4 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Pin Configurations (continued)
165-Ball FBGA (15 x 17 x 1.4 mm) Pinout
CY7C1248V18 (2M x 18)
1
2
3
A
4
5
6
7
8
9
A
10
A
11
CQ
DQ8
NC
NC/72M
NC/144M
A
B
C
D
CQ
NC
NC
NC
R/W
A
BWS1
NC/288M
A
K
K
LD
A
DQ9
NC
NC
NC
NC
NC
NC
NC
DQ7
NC
BWS0
A
VSS
VSS
NC
VSS
VSS
VSS
NC
DQ10
VSS
VSS
NC
NC
NC
NC
NC
DQ12
NC
DQ11
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
NC
NC
NC
NC
DQ6
E
F
VDD
VDD
VDD
VDD
VDD
VSS
DQ5
NC
DQ13
VDDQ
NC
NC
NC
G
H
J
VREF
NC
VDDQ
NC
VREF
DQ4
NC
ZQ
DOFF
NC
NC
NC
NC
NC
NC
NC
NC
DQ14
NC
NC
DQ3
DQ2
K
L
DQ15
NC
NC
NC
NC
NC
NC
VSS
VSS
VSS
A
VSS
A
VSS
A
VSS
VSS
NC
NC
NC
DQ1
NC
NC
NC
M
N
P
DQ16
DQ17
A
QVLD
A
NC
DQ0
A
A
A
A
A
A
TDO
TCK
A
A
TMS
TDI
R
NC
CY7C1250V18 (1M x 36)
1
2
3
A
4
5
6
7
8
9
A
10
NC/72M
11
CQ
NC/144M
A
B
C
D
R/W
A
BWS2
BWS3
A
K
K
LD
A
CQ
NC
BWS1
BWS0
A
DQ27
NC
DQ18
DQ28
DQ19
NC
NC
NC
NC
DQ17
NC
DQ8
DQ7
DQ16
NC
NC
NC
NC
NC
VSS
VSS
NC
VSS
VSS
VSS
DQ29
VSS
VSS
NC
DQ30
DQ31
VREF
NC
DQ20
DQ21
DQ22
VDDQ
DQ32
DQ23
DQ24
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
NC
NC
DQ15
NC
DQ6
E
F
VDD
VDD
VDD
VDD
VDD
VSS
DQ5
DQ14
ZQ
NC
NC
G
H
J
VDDQ
NC
VREF
DQ13
DQ12
NC
DOFF
NC
DQ4
DQ3
DQ2
NC
NC
NC
NC
K
L
DQ33
NC
NC
NC
NC
NC
DQ35
NC
DQ34
DQ25
DQ26
VSS
VSS
VSS
A
VSS
A
VSS
A
VSS
VSS
NC
NC
NC
DQ11
NC
DQ1
DQ10
DQ0
M
N
P
A
QVLD
A
DQ9
A
A
A
A
A
A
TDO
TCK
A
A
TMS
TDI
R
NC
Document Number: 001-06348 Rev. *D
Page 5 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Pin Definitions
Pin Name
IO
Pin Description
Data Input/Output Signals. Inputs are sampled on the rising edge of K and K clocks during
valid write operations. These pins drive out the requested data during a read operation. Valid
data is driven out on the rising edge of both the K and K clocks during read operations. When
DQ
Input/Output-
Synchronous
[x:0]
read access is deselected, Q
are automatically tri-stated.
[x:0]
CY7C1246V18 − DQ
[7:0]
CY7C1257V18 − DQ
[8:0]
CY7C1248V18 − DQ
[17:0]
CY7C1250V18 − DQ
[35:0]
LD
Input-
Synchronous Load. This input is brought LOW when a bus cycle sequence is to be defined.
Synchronous This definition includes address and read/write direction. All transactions operate on a burst of
2 data. LD must meet the setup and hold times around edge of K.
NWS , NWS Input-
Nibble Write Select 0, 1, Active LOW (CY7C1246V18 only). Sampled on the rising edge of
Synchronous the K and K clocks during write operations. Used to select which nibble is written into the device
during the current portion of the write operations. Nibbles not written remain unaltered.
0
1
NWS controls D
and NWS controls D
.
0
[3:0]
1
[7:4]
All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble
Write Select ignores the corresponding nibble of data and not written into the device.
BWS BWS
Input-
Byte Write Select 0, 1, 2, and 3, Active LOW. Sampled on the rising edge of the K and K clocks
,
,
0
1
3
Synchronous during write operations. Used to select which byte is written into the device during the current
portion of the write operations. Bytes not written remain unaltered.
CY7C1257V18 − BWS controls D
BWS , BWS
2
0
[8:0]
[8:0]
CY7C1248V18 − BWS controls D
and BWS controls D
0
1
[17:9].
, BWS controls D
CY7C1250V18 − BWS controls D
, BWS controls D
and BWS
0
[8:0]
1
[17:9]
2
[26:18] 3
controls D
.
[35:27]
All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write
Select ignores the corresponding byte of data and not written into the device.
A
Input-
Address Inputs. Sampled on the rising edge of the K clock during active read and write opera-
Synchronous tions. These address inputs are multiplexed for both read and write operations. Internally, the
device is organized as 4M x 8 (2 arrays each of 2M x 8) for CY7C1246V18, 4M x 9 (2 arrays
each of 2M x 9) for CY7C1257V18, 2M x 18 (2 arrays each of 1M x 18) for CY7C1248V18, and
1M x 36 (2 arrays each of 512K x 36) for CY7C1250V18.
R/W
Input-
Synchronous Read/Write Input. When LD is LOW, this input designates the access type (read
Synchronous when R/W is HIGH, write when R/W is LOW) for loaded address. R/W must meet the setup and
hold times around edge of K.
QVLD
K
Valid output Valid Output Indicator. The Q Valid indicates valid output data. QVLD is edge aligned with CQ
indicator
and CQ.
Input-
Clock
Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the
device and to drive out data through Q
on the rising edge of K.
when in single clock mode. All accesses are initiated
[x:0]
K
Input-
Clock
Negative Input Clock Input. K is used to capture synchronous data being presented to the
device and to drive out data through Q when in single clock mode.
[x:0]
CQ
Clock Output Synchronous Echo Clock Outputs. This is a free running clock and is synchronized to the
CQ
Synchronous Echo Clock Outputs. This is a free running clock and is synchronized to the
Clock Output
Document Number: 001-06348 Rev. *D
Page 6 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Pin Definitions (continued)
Pin Name
ZQ
IO
Pin Description
Input
Output Impedance Matching Input. This input is used to tune the device outputs to the system
data bus impedance. CQ, CQ, and Q output impedance are set to 0.2 x RQ, where RQ is a
[x:0]
resistor connected between ZQ and ground. Alternatively, this pin can be connected directly to
V
, which enables the minimum impedance mode. This pin cannot be connected directly to
DDQ
GND or left unconnected.
DOFF
Input
DLL Turn Off, Active LOW. Connecting this pin to ground turns off the DLL inside the device.
The timing in the DLL turned off operation is different from that listed in this data sheet. For
normal operation, this pin can be connected to a pull up through a 10 Kohm or less pull up
resistor. The device behaves in DDR-I mode when the DLL is turned off. In this mode, the device
can be operated at a frequency of up to 167 MHz with DDR-I timing.
TDO
Output
Input
Input
Input
N/A
TDO for JTAG.
TCK
TCK Pin for JTAG.
TDI
TDI Pin for JTAG.
TMS
TMS Pin for JTAG.
NC
Not Connected to the Die. Can be tied to any voltage level.
Not Connected to the Die. Can be tied to any voltage level.
Not Connected to the Die. Can be tied to any voltage level.
Not Connected to the Die. Can be tied to any voltage level.
Reference Voltage Input. Static input used to set the reference level for HSTL inputs, outputs,
NC/72M
NC/144M
NC/288M
N/A
N/A
N/A
V
Input-
REF
Reference and AC measurement points.
V
V
V
Power Supply Power Supply Inputs to the Core of the Device.
DD
Ground
Ground for the Device.
SS
Power Supply Power Supply Inputs for the Outputs of the Device.
DDQ
Document Number: 001-06348 Rev. *D
Page 7 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
When write access is deselected, the device ignores all inputs
after the pending write operations are completed.
Functional Overview
The CY7C1246V18, CY7C1257V18, CY7C1248V18, and
CY7C1250V18 are synchronous pipelined Burst SRAMs
equipped with a DDR interface.
Byte Write Operations
Byte write operations are supported by the CY7C1248V18. A
write operation is initiated as described in the Write Operations
section. The bytes that are written are determined by BWS and
Accesses for both ports are initiated on the Positive Input Clock
(K). All synchronous input and output timing refer to the rising
edge of the input clocks (K and K).
0
BWS , which are sampled with each set of 18-bit data words.
1
Asserting the appropriate Byte Write Select input during the data
portion of a write latches the data being presented and written
into the device. Deasserting the Byte Write Select input during
the data portion of a write enables the data stored in the device
for that byte to remain unaltered. This feature can be used to
simplify read/modify/write operations to a byte write operation.
All synchronous data inputs (D
) pass through input registers
[x:0]
controlled by the rising edge of the input clocks (K and K). All
synchronous data outputs (Q ) pass through output registers
[x:0]
controlled by the rising edge of the input clocks (K and K).
All synchronous control (R/W, LD, BWS ) inputs pass through
input registers controlled by the rising edge of the input clock
(K\K).
[0:X]
Double Data Rate Operation
The CY7C1248V18 enables high-performance operation
through high clock frequencies (achieved through pipelining) and
DDR mode of operation. The CY7C1248V18 requires two No
Operation (NOP) cycles when transitioning from a read to a write
cycle. At higher frequencies, some applications may require a
third NOP cycle to avoid contention.
CY7C1248V18 is described in the following sections. The same
basic descriptions apply to CY7C1246V18, CY7C1257V18, and
CY7C1250V18.
Read Operations
The CY7C1248V18 is organized internally as a single array of
2M x 18. Accesses are completed in a burst of two sequential
18-bit data words. Read operations are initiated by asserting
R/W HIGH and LD LOW at the rising edge of the positive input
clock (K). Following the next two K clock rising edges, the corre-
sponding 18-bit word of data from this address location is driven
If a read occurs after a write cycle, address and data for the write
are stored in registers. The write information must be stored
because the SRAM cannot perform the last word write to the
array without conflicting with the read. The data stays in this
register until the next write cycle occurs. On the first write cycle
after the read(s), the stored data from the earlier write is written
into the SRAM array. This is called a Posted Write.
onto the Q
using K as the output timing reference. On the
[17:0]
subsequent rising edge of K the next 18-bit data word is driven
onto the Q . The requested data is valid 0.45 ns from the
[17:0]
If a read is performed on the same address on which a write is
performed in the previous cycle, the SRAM reads out the most
current data. The SRAM does this by bypassing the memory
array and reading the data from the registers.
rising edge of the input clock (K and K). To maintain the internal
logic, each read access must be allowed to complete. Read
accesses can be initiated on every rising edge of the positive
input clock (K).
Depth Expansion
When read access is deselected, the CY7C1248V18 completes
the pending read transactions. Synchronous internal circuitry
automatically tri-states the outputs following the next rising edge
of the positive input clock (K). This enables a seamless transition
between devices without the insertion of wait states in a depth
expanded memory.
Depth expansion requires replicating the LD control signal for
each bank. All other control signals can be common between
banks as appropriate.
Programmable Impedance
An external resistor, RQ, must be connected between the ZQ pin
Write Operations
on the SRAM and V to enable the SRAM to adjust its output
SS
Write operations are initiated by asserting R/W LOW and LD
LOW at the rising edge of the positive input clock (K). The
address presented to Address inputs is stored in the Write
Address register. On the following K clock rise, the data
driver impedance. The value of RQ must be 5x the value of the
intended line impedance driven by the SRAM. The allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15%, is between 175Ω and 350Ω, with V
= 1.5V. The
DDQ
presented to D
is latched and stored into the 18-bit Write
[17:0]
output impedance is adjusted every 1024 cycles upon power up
to account for drifts in supply voltage and temperature.
Data register, provided BWS
subsequent rising edge of the Negative Input Clock (K), the infor-
mation presented to D is also stored into the Write Data
are both asserted active. On the
[1:0]
Echo Clocks
[17:0]
register, provided BWS
are both asserted active. The 36 bits
[1:0]
Echo clocks are provided on the DDR-II+ to simplify data capture
on high speed systems. Two echo clocks are generated by the
DDR-II+. CQ is referenced with respect to K and CQ is refer-
enced with respect to K. These are free-running clocks and are
synchronized to the input clock of the DDR-II+. The timing for the
of data are then written into the memory array at the specified
location. Write accesses can be initiated on every rising edge of
the positive input clock (K). Doing so pipelines the data flow such
that 18 bits of data can be transferred into the device on every
rising edge of the input clocks (K and K).
Document Number: 001-06348 Rev. *D
Page 8 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
be disabled by applying ground to the DOFF pin. When the DLL
is turned off, the device behaves in DDR-I mode (with 1.0 cycle
latency and a longer access time). For more information, refer to
Valid Data Indicator (QVLD)
QVLD is provided on the DDR-II+ to simplify data capture on high
speed systems. The QVLD is generated by the DDR-II+ device
along with data output. This signal is also edge aligned with the
echo clock and follows the timing of any data pin. This signal is
asserted half a cycle before valid data arrives.
the
application
note,
DLL
Considerations
in
QDRII/DDRII/QDRII+/DDRII+. The DLL can also be reset by
slowing or stopping the input clocks K and K for a minimum of 30
ns. However, it is not necessary for the DLL to be reset to lock to
the desired frequency. During power up, when the DOFF is tied
HIGH, the DLL gets locked after 2048 cycles of stable clock.
Delay Lock Loop (DLL)
These chips use a DLL that is designed to function between 120
MHz and the specified maximum clock frequency. The DLL may
Application Example
Figure 1 shows the use of two DDR-II+ in an application.
Figure 1. Application Example
ZQ
CQ/CQ
K
K
ZQ
CQ/CQ
K
K
SRAM#1
LD R/W
SRAM#2
DQ
A
DQ
A
R = 250ohms
R = 250ohms
LD R/W
DQ
Addresses
Cycle Start
R/W
Source CLK
Source CLK
BUS
MASTER
(CPU or ASIC)
Echo Clock1/Echo Clock1
Echo Clock2/Echo Clock2
Truth Table
The truth table for the CY7C1246V18, CY7C1257V18, CY7C1248V18, and CY7C1250V18 follows.
Operation
K
LD R/W
DQ
DQ
Write Cycle:
L-H
L
L
L
D(A) at K(t + 1) ↑
D(A + 1) at K(t + 1) ↑
Load address; wait one cycle; input write data on consecutive
K and K rising edges.
Read Cycle: (2.0 cycle Latency)
Load address; wait two cycle; read data on consecutive K and
L-H
H
Q(A) at K(t + 2) ↑
Q(A + 1) at K(t + 2) ↑
K rising edges.
NOP: No Operation
L-H
H
X
X
X
High-Z
High-Z
Standby: Clock Stopped
Stopped
Previous State
Previous State
Notes
2. X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑ represents rising edge.
3. Device powers up deselected with the outputs in a tri-state condition.
4. “A” represents address location latched by the devices when transaction was initiated. A + 1 represents the address sequence in the burst.
5. “t” represents the cycle at which a read/write operation is started. t + 1 and t + 2 are the first and second clock cycles succeeding the “t” clock cycle.
6. Data inputs are registered at K and K rising edges. Data outputs are delivered on K and K rising edges.
7. Cypress recommends that K = K = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging
symmetrically.
Document Number: 001-06348 Rev. *D
Page 9 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Write Cycle Descriptions
The write cycle descriptions table for CY7C1246V18 and CY7C1248V18 follows.
BWS / BWS /
0
1
K
Comments
K
NWS
NWS
1
0
L
L
L
L
L–H
–
During the data portion of a write sequence:
CY7C1246V18 − both nibbles (D
) are written into the device.
[7:0]
CY7C1248V18 − both bytes (D
) are written into the device.
[17:0]
–
L–H
–
L-H During the data portion of a write sequence:
CY7C1246V18 − both nibbles (D
) are written into the device.
) are written into the device.
[7:0]
CY7C1248V18 − both bytes (D
[17:0]
L
H
H
L
–
During the data portion of a write sequence:
CY7C1246V18 − only the lower nibble (D
) is written into the device, D
) is written into the device, D
remains unaltered.
remains unaltered.
[3:0]
[7:4]
[17:9]
CY7C1248V18 − only the lower byte (D
[8:0]
L
L–H During the data portion of a write sequence:
CY7C1246V18 − only the lower nibble (D
) is written into the device, D
remains unaltered.
remains unaltered.
[3:0]
[7:4]
CY7C1248V18 − only the lower byte (D
) is written into the device, D
[8:0]
[17:9]
H
H
L–H
–
–
During the data portion of a write sequence:
CY7C1246V18 − only the upper nibble (D
) is written into the device, D
) is written into the device, D
remains unaltered.
remains unaltered.
[7:4]
[3:0]
[8:0]
CY7C1248V18 − only the upper byte (D
[17:9]
L
L–H During the data portion of a write sequence:
CY7C1246V18 − only the upper nibble (D
) is written into the device, D
) is written into the device, D
remains unaltered.
remains unaltered.
[7:4]
[3:0]
[8:0]
CY7C1248V18 − only the upper byte (D
[17:9]
H
H
H
H
L–H
–
–
No data is written into the devices during this portion of a write operation.
L–H No data is written into the devices during this portion of a write operation.
Write Cycle Descriptions
The write cycle descriptions table for CY7C1257V18 follows.
BWS
K
L-H
–
K
Comments
During the data portion of a write sequence, the single byte (D
0
L
L
–
) is written into the device.
) is written into the device.
[8:0]
[8:0]
L-H During the data portion of a write sequence, the single byte (D
H
H
L-H
–
–
No data is written into the device during this portion of a write operation.
L-H No data is written into the device during this portion of a write operation.
Note
8. Assumes a write cycle was initiated per the Write Cycle Descriptions table. NWS , NWS , BWS , BWS , BWS , and BWS can be altered on different portions
0
1
0
1
2
3
of a write cycle, as long as the setup and hold requirements are met.
Document Number: 001-06348 Rev. *D
Page 10 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Write Cycle Descriptions
The write cycle descriptions table for CY7C1250V18 follows.
BWS
BWS
BWS
BWS
3
K
K
Comments
0
1
2
L
L
L
L
L-H
–
During the data portion of a write sequence, all four bytes (D
into the device.
) are written
) are written
[35:0]
L
L
L
H
H
L
L
H
H
H
H
L
L
H
H
H
H
H
H
L
–
L-H
–
L-H During the data portion of a write sequence, all four bytes (D
into the device.
[35:0]
–
During the data portion of a write sequence, only the lower byte (D
) is
) is
[8:0]
written into the device. D
remains unaltered.
[35:9]
L
L-H During the data portion of a write sequence, only the lower byte (D
written into the device. D remains unaltered.
[8:0]
[35:9]
H
H
H
H
H
H
L-H
–
–
During the data portion of a write sequence, only the byte (D
) is written
[17:9]
into the device. D
and D
remain unaltered.
[8:0]
[35:18]
L
L-H During the data portion of a write sequence, only the byte (D
into the device. D and D remain unaltered.
) is written
[17:9]
[8:0]
[35:18]
H
H
H
H
L-H
–
–
During the data portion of a write sequence, only the byte (D
) is written
) is written
) is written
) is written
[26:18]
[26:18]
[35:27]
[35:27]
into the device. D
and D
remain unaltered.
[17:0]
[35:27]
L
L-H During the data portion of a write sequence, only the byte (D
into the device. D and D remain unaltered.
[17:0]
[35:27]
H
H
L-H
–
–
During the data portion of a write sequence, only the byte (D
into the device. D remains unaltered.
[26:0]
L
L-H During the data portion of a write sequence, only the byte (D
into the device. D remains unaltered.
[26:0]
H
H
H
H
H
H
H
H
L-H
–
–
No data is written into the device during this portion of a write operation.
L-H No data is written into the device during this portion of a write operation.
Document Number: 001-06348 Rev. *D
Page 11 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Instruction Register
IEEE 1149.1 Serial Boundary Scan (JTAG)
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO pins as shown in “TAP Controller Block Diagram” on
page 15. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
These SRAMs incorporate a serial boundary scan test access
port (TAP) in the FBGA package. This part is fully compliant with
IEEE Standard #1149.1-2001. The TAP operates using JEDEC
standard 1.8V IO logic levels.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary ‘01’ pattern to enable fault
isolation of the board level serial test path.
feature. To disable the TAP controller, tie TCK LOW (V ) to
SS
prevent device clocking. TDI and TMS are internally pulled up
and may be unconnected. They may alternately be connected to
V
through a pull up resistor. TDO must be left unconnected.
Bypass Register
DD
Upon power up, the device comes up in a reset state which does
not interfere with the operation of the device.
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between TDI
and TDO pins. This shifts data through the SRAM with minimal
delay. The bypass register is set LOW (V ) when the BYPASS
instruction is executed.
Test Access Port – Test Clock
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
SS
Boundary Scan Register
Test Mode Select
The boundary scan register is connected to all of the input and
output pins on the SRAM. Several no connect (NC) pins are also
included in the scan register to reserve pins for higher density
devices.
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. You can leave this pin
unconnected if the TAP is not used. The pin is pulled up inter-
nally, resulting in a logic HIGH level.
The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and TDO
pins when the controller is moved to the Shift-DR state. The
EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions can
be used to capture the contents of the input and output ring.
Test Data-In (TDI)
The TDI pin is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information about
loading the instruction register, see “TAP Controller State
Diagram” on page 14. TDI is internally pulled up and can be
unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) on any register.
“Boundary Scan Order” on page 18 shows the order in which the
bits are connected. Each bit corresponds to one of the bumps on
the SRAM package. The MSB of the register is connected to TDI,
and the LSB is connected to TDO.
Identification (ID) Register
Test Data-Out (TDO)
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in “Identification Register Definitions” on
The TDO output pin is used to serially clock data-out from the
registers. Whether the output is active depends on the current
state of the TAP state machine (see “Instruction Codes” on
page 17). The output changes on the falling edge of TCK. TDO
is connected to the least significant bit (LSB) of any register.
Performing a TAP Reset
A reset is performed by forcing TMS HIGH (V ) for five rising
TAP Instruction Set
DD
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating. At
power up, the TAP is reset internally to ensure that TDO comes
up in a High-Z state.
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in “Instruction
RESERVED and must not be used. The other five instructions
are described in this section in detail.
TAP Registers
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO pins. To execute
the instruction after it is shifted in, the TAP controller must be
moved into the Update-IR state.
Registers are connected between the TDI and TDO pins and
scans data into and out of the SRAM test circuitry. Only one
register can be selected at a time through the instruction
registers. Data is serially loaded into the TDI pin on the rising
edge of TCK. Data is output on the TDO pin on the falling edge
of TCK.
Document Number: 001-06348 Rev. *D
Page 12 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
IDCODE
PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells before the selection
of another boundary scan test operation.
The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO pins and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state. The
IDCODE instruction is loaded into the instruction register upon
power up or whenever the TAP controller is in a Test-Logic-Reset
state.
The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required — that is, while data captured
is shifted out, the preloaded data can be shifted in.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. The SAMPLE Z command puts the output bus
into a High-Z state until the next command is issued during the
Update-IR state.
EXTEST
The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the Shift-DR controller state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
EXTEST Output Bus Tri-State
IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tri-state mode.
Be aware that the TAP controller clock can only operate at a
frequency up to 20 MHz, while the SRAM clock operates more
than an order of magnitude faster. Because there is a large
difference in the clock frequencies, it is possible that during the
Capture-DR state, an input or output may undergo a transition.
The TAP may then try to capture a signal while in transition
(metastable state). This does not harm the device, but there is
no guarantee as to the value that is captured. Repeatable results
may not be possible.
The boundary scan register has a special bit located at bit #108.
When this scan cell, called the “extest output bus tri-state,” is
latched into the preload register during the Update-DR state in
the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it enables the output buffers to drive the
output bus. When LOW, this bit places the output bus into a
High-Z condition.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus hold
times (t and t ). The SRAM clock input might not be captured
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the CK and CK captured in the boundary scan register.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that cell,
during the Shift-DR state. During Update-DR, the value loaded
into that shift-register cell latches into the preload register. When
the EXTEST instruction is entered, this bit directly controls the
output Q-bus pins. Note that this bit is preset HIGH to enable the
output when the device is powered-up, and also when the TAP
controller is in the Test-Logic-Reset state.
CS
CH
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
Document Number: 001-06348 Rev. *D
Page 13 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
TAP Controller State Diagram
The state diagram for the TAP controller follows.
[9]
TEST-LOGIC
1
RESET
0
1
1
1
TEST-LOGIC/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
0
0
0
1
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
0
1
1
EXIT1-DR
0
1
EXIT1-IR
0
1
0
0
PAUSE-DR
1
PAUSE-IR
1
0
0
EXIT2-DR
1
EXIT2-IR
1
UPDATE-DR
UPDATE-IR
1
1
0
0
Note
9. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.
Document Number: 001-06348 Rev. *D
Page 14 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
TAP Controller Block Diagram
0
Bypass Register
Selection
Circuitry
Selection
Circuitry
2
1
1
0
TDO
TDI
Instruction Register
29
31 30
.
.
2
0
0
Identification Register
.
.
.
.
2
1
108
Boundary Scan Register
TCK
TMS
TAP Controller
TAP Electrical Characteristics
Over the Operating Range
Parameter
Description
Test Conditions
= −2.0 mA
Min
1.4
1.6
Max
Unit
V
V
V
V
V
V
V
I
Output HIGH Voltage
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Input HIGH Voltage
I
I
I
I
OH1
OH2
OL1
OL2
IH
OH
OH
OL
OL
= −100 μA
= 2.0 mA
V
0.4
0.2
V
= 100 μA
V
0.65V
V
+ 0.3
V
DD
DD
Input LOW Voltage
–0.3
0.35V
5
V
IL
DD
Input and Output Load Current
GND ≤ V ≤ V
DD
−5
μA
X
I
Notes
10. These characteristics apply to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in “Electrical Characteristics” on page 20.
11. Overshoot: V (AC) < V + 0.3V (pulse width less than t /2).
/2). Undershoot: V (AC) > − 0.3V (pulse width less than t
IH
DDQ
CYC
IL
CYC
12. All voltage refers to ground.
Document Number: 001-06348 Rev. *D
Page 15 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
TAP AC Switching Characteristics
Over the Operating Range
Parameter
Description
Min
Max
Unit
ns
t
t
t
t
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH
50
TCYC
TF
20
MHz
ns
20
20
TH
TCK Clock LOW
ns
TL
Setup Times
t
t
t
TMS Setup to TCK Clock Rise
TDI Setup to TCK Clock Rise
Capture Setup to TCK Rise
5
5
5
ns
ns
ns
TMSS
TDIS
CS
Hold Times
t
t
t
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
5
5
5
ns
ns
ns
TMSH
TDIH
CH
Capture Hold after Clock Rise
Output Times
t
t
TCK Clock LOW to TDO Valid
TCK Clock LOW to TDO Invalid
10
ns
ns
TDOV
TDOX
0
TAP Timing and Test Conditions
Figure 2 shows the TAP timing and test conditions.
Figure 2. TAP Timing and Test Conditions
0.9V
ALL INPUT PULSES
0.9V
50Ω
1.8V
TDO
0V
Z = 50Ω
0
C = 20 pF
L
t
t
TL
TH
GND
(a)
Test Clock
TCK
t
TCYC
t
TMSH
t
TMSS
Test Mode Select
TMS
t
TDIS
t
TDIH
Test Data In
TDI
Test Data Out
TDO
t
TDOV
t
TDOX
Notes
13. t and t refer to the setup and hold time requirements of latching data from the boundary scan register.
CS
CH
14. Test conditions are specified using the load in TAP AC Test Conditions. t /t = 1 ns.
R
F
Document Number: 001-06348 Rev. *D
Page 16 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Identification Register Definitions
Value
Instruction
Field
Description
CY7C1246V18
CY7C1257V18
000
CY7C1248V18
CY7C1250V18
Revision
000
000
000
Version number.
Number (31:29)
Cypress Device 11010111100000111 11010111100001111 11010111100010111 11010111100100111 Defines the type
ID (28:12)
of SRAM.
Cypress JEDEC
ID (11:1)
00000110100
1
00000110100
1
00000110100
1
00000110100
1
Enables unique
identification of
SRAM vendor.
ID Register
Presence (0)
Indicates the
presence of an
ID register.
Scan Register Sizes
Register Name
Bit Size
Instruction
Bypass
3
1
ID
32
109
Boundary Scan
Instruction Codes
Instruction
EXTEST
Code
000
Description
Captures the input/output ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between
TDI and TDO. This operation does not affect SRAM operation.
SAMPLE Z
010
Captures the input/output contents. Places the boundary scan register between
TDI and TDO. Forces all SRAM output drivers to a High-Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures the input/output ring contents. Places the boundary scan register
between TDI and TDO. Does not affect the SRAM operation.
RESERVED
RESERVED
BYPASS
101
110
111
Do Not Use: This instruction is reserved for future use.
Do Not Use: This instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not affect
SRAM operation.
Document Number: 001-06348 Rev. *D
Page 17 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Boundary Scan Order
Bit #
0
Bump ID
6R
Bit #
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Bump ID
10G
9G
Bit #
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
Bump ID
6A
5B
5A
4A
5C
4B
3A
2A
1A
2B
3B
1C
1B
3D
3C
1D
2C
3E
2D
2E
1E
2F
Bit #
84
Bump ID
1J
1
6P
85
2J
2
6N
11F
11G
9F
86
3K
3
7P
87
3J
4
7N
88
2K
5
7R
10F
11E
10E
10D
9E
89
1K
6
8R
90
2L
7
8P
91
3L
8
9R
92
1M
1L
9
11P
10P
10N
9P
93
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
10C
11D
9C
94
3N
95
3M
1N
96
10M
11N
9M
9D
97
2M
3P
11B
11C
9B
98
99
2N
9N
100
101
102
103
104
105
106
107
108
2P
11L
11M
9L
10B
11A
10A
9A
1P
3R
4R
10L
11K
10K
9J
4P
8B
5P
7C
3F
5N
6C
1G
1F
5R
9K
8A
Internal
10J
11J
11H
7A
3G
2G
1H
7B
6B
Document Number: 001-06348 Rev. *D
Page 18 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
DLL Constraints
Power Up Sequence in DDR-II+ SRAM
DDR-II+ SRAMs must be powered up and initialized in a
predefined manner to prevent undefined operations. During
power up, when the DOFF is tied HIGH, the DLL is locked after
2048 cycles of stable clock.
■ DLL uses K clock as its synchronizing input. The input must
have low phase jitter, which is specified as t
.
KC Var
■ The DLL functions at frequencies down to 120 MHz.
■ If the input clock is unstable and the DLL is enabled, then the
DLL may lock onto an incorrect frequency, causing unstable
SRAM behavior. Toavoid this, provide 2048 cycles stable clock
to relock to the desired clock frequency.
Power Up Sequence
■ ApplypowerwithDOFFtiedHIGH(allotherinputscanbeHIGH
or LOW)
❐ Apply V before V
DD
DDQ
❐ Apply V
before V
or at the same time as V
DDQ
REF REF
■ Provide stable power and clock (K, K) for 2048 cycles to lock
the DLL
Power Up Waveforms
Figure 3. Power Up Waveforms
K
K
Start Normal
Operation
Unstable Clock
> 2048 Stable Clock
Clock Start (Clock Starts after V /V
DD DDQ
is Stable)
V
/V
+
V
/V Stable (< 0.1V DC per 50 ns)
DD DDQ
DD DDQ
Fix HIGH (tie to V
DDQ
)
DOFF
Document Number: 001-06348 Rev. *D
Page 19 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Current into Outputs (LOW)......................................... 20 mA
Static Discharge Voltage (MIL-STD-883, M 3015).... >2001V
Latch up Current..................................................... >200 mA
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................ –65°C to + 150°C
Ambient Temperature with Power Applied. –55°C to + 125°C
Operating Range
Ambient
DD
V
DDQ
Range
Com’l
Ind’l
Temperature
0°C to +70°C
–40°C to +85°C
V
Supply Voltage on V Relative to GND .......–0.5V to + 2.9V
DD
1.8 ± 0.1V
1.4V to V
DD
Supply Voltage on V
Relative to GND..... –0.5V to + V
DD
DDQ
DC Applied to Outputs in High-Z .........–0.5V to V
+ 0.3V
DDQ
DC Input Voltage ............................... –0.5V to V + 0.3V
DD
Electrical Characteristics
Over the Operating Range
DC Electrical Characteristics
Parameter
Description
Power Supply Voltage
IO Supply Voltage
Test Conditions
Min
1.7
1.4
Typ
Max
Unit
V
1.8
1.5
1.9
V
V
V
V
V
V
V
V
DD
V
V
V
V
V
V
V
I
V
DD
DDQ
OH
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
V
V
/2 – 0.12
V
V
/2 + 0.12
/2 + 0.12
DDQ
DDQ
DDQ
/2 – 0.12
OL
DDQ
I
I
= –0.1 mA, Nominal Impedance
= 0.1 mA, Nominal Impedance
V
– 0.2
V
DDQ
OH(LOW)
OL(LOW)
IH
OH
OL
DDQ
V
0.2
SS
V
+ 0.1
V
+ 0.15
REF
DDQ
–0.15
V
– 0.1
IL
REF
Input Leakage Current
Output Leakage Current
Input Reference Voltage
GND ≤ V ≤ V
–2
–2
2
μA
μA
V
X
I
DDQ
I
GND ≤ V ≤ V
Output Disabled
2
OZ
I
DDQ,
V
Typical Value = 0.75V
0.68
0.75
0.95
1000
1080
1210
290
REF
I
V
Operating Supply
V
= Max., I
= 0 mA, 300 MHz
333 MHz
mA
mA
mA
mA
mA
mA
DD
DD
DD
OUT
CYC
f = f
= 1/t
MAX
375 MHz
I
Automatic Power Down
Current
Max. V
,
300 MHz
SB1
DD
Both Ports Deselected,
333 MHz
375 MHz
300
V
≥ V or V ≤ V
IN
IH
IN
IL
f = f
= 1/t
,
320
MAX
CYC
Inputs Static
AC Input Requirements
Over the Operating Range
Parameter Description
Test Conditions
Min
Typ.
Max
Unit
V
V
Input HIGH Voltage
Input LOW Voltage
V
+ 0.2
–
–
V
+ 0.24
DDQ
IH
REF
V
–0.24
V
– 0.2
V
IL
REF
Notes
15. Power up: assumes a linear ramp from 0V to V (min) within 200 ms. During this time V < V and V
< V .
DD
DD
IH
DD
DDQ
16. Outputs are impedance controlled. I = –(V
/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.
OH
DDQ
17. Outputs are impedance controlled. I = (V
/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.
OL
DDQ
18. V
(min) = 0.68V or 0.46V
, whichever is larger. V
(max) = 0.95V or 0.54V
, whichever is smaller.
DDQ
REF
DDQ
REF
19. The operation current is calculated with 50% read cycle and 50% write cycle.
Document Number: 001-06348 Rev. *D
Page 20 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
\
Capacitance
Tested initially and after any design or process change that may affect these parameters.
Parameter
Description
Input Capacitance
Test Conditions
T = 25°C, f = 1 MHz,
Max
Unit
pF
C
5
4
5
IN
A
V
= 1.8V
DD
V
C
C
Clock Input Capacitance
Output Capacitance
pF
CLK
O
= 1.5V
DDQ
pF
Thermal Resistance
Tested initially and after any design or process change that may affect these parameters.
165 FBGA
Package
Parameter
Description
Test Conditions
Unit
Θ
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard test methods and
procedures for measuring thermal impedance, per
EIA/JESD51.
16.25
°C/W
JA
Θ
Thermal Resistance
(Junction to Case)
2.91
°C/W
JC
AC Test Loads and Waveforms
Figure 4. AC Test Loads and Waveforms
VREF = 0.75V
0.75V
VREF
VREF
0.75V
R = 50Ω
OUTPUT
[20]
ALL INPUT PULSES
1.25V
Z = 50Ω
0
OUTPUT
Device
Under
Test
R = 50Ω
L
0.75V
Device
Under
0.25V
5 pF
VREF = 0.75V
Slew Rate = 2 V/ns
ZQ
Test
ZQ
RQ =
RQ =
250Ω
250Ω
INCLUDING
JIG AND
SCOPE
(a)
(b)
Note
20. Unless otherwise noted, test conditions assume signal transition time of 2V/ns, timing reference levels of 0.75V, V
= 0.75V, RQ = 250Ω, V
= 1.5V, input
REF
DDQ
pulse levels of 0.25V to 1.25V, and output loading of the specified I /I and load capacitance shown in (a) of AC Test Loads and Waveforms.
OL OH
Document Number: 001-06348 Rev. *D
Page 21 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Switching Characteristics
Over the Operating Range
375 MHz
333 MHz
300 MHz
Cypress Consortium
Parameter Parameter
Description
Unit
Min Max Min Max Min Max
t
t
t
t
t
V
(Typical) to the first Access
1
–
1
–
1
–
ms
ns
POWER
CYC
KH
DD
t
t
t
t
K Clock Cycle Time
2.66 8.4 3.0 8.4 3.3 8.4
KHKH
KHKL
KLKH
KHKH
Input Clock (K/K) HIGH
Input Clock (K/K) LOW
0.4
0.4
–
–
–
0.4
0.4
–
–
–
0.4
0.4
–
–
–
t
t
CYC
KL
CYC
K Clock Rise to K Clock Rise (rising edge to rising edge) 1.13
1.28
1.40
ns
KHKH
Setup Times
t
t
t
t
t
t
Address Setup to K Clock Rise
0.4
0.4
–
–
–
0.4
0.4
–
–
–
0.4
0.4
–
–
–
ns
ns
ns
SA
AVKH
IVKH
IVKH
Control Setup to K Clock Rise (LD, R/W)
SC
Double Data Rate Control Setup to Clock (K, K) Rise
0.28
0.28
0.28
SCDDR
(BWS , BWS , BWS , BWS )
0
1
2
3
t
t
D Setup to Clock (K/K) Rise
[X:0]
0.28
–
0.28
–
0.28
–
ns
SD
DVKH
Hold Times
t
t
t
t
t
t
0.4
0.4
–
–
–
0.4
0.4
–
–
–
0.4
0.4
–
–
–
ns
ns
ns
Address Hold after K Clock Rise
HA
KHAX
KHIX
KHIX
Control Hold after K Clock Rise (LD, R/W)
HC
Double Data Rate Control Hold after Clock (K/K) Rise
0.28
0.28
0.28
HCDDR
(BWS , BWS , BWS , BWS )
0
1
2
3
t
t
D Hold after Clock (K/K) Rise
[X:0]
0.28
–
0.28
–
0.28
–
ns
HD
KHDX
Output Times
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
K/K Clock Rise to Data Valid
–
0.45
–
–
–0.45
–
0.45
–
–
–0.45
–
0.45
–
ns
ns
ns
ns
ns
ns
ns
ns
CO
CHQV
Data Output Hold after K/K Clock Rise (Active to Active) –0.45
DOH
CHQX
–
0.45
–
0.45
–
0.45
–
K/K Clock Rise to Echo Clock Valid
Echo Clock Hold after K/K Clock Rise
Echo Clock High to Data Valid
CCQO
CQOH
CQD
CHCQV
CHCQX
CQHQV
CQHQX
CQHCQL
CQHCQH
–0.45
–
–0.45
–
–0.45
–
0.2
–
0.2
–
0.2
–
Echo Clock High to Data Invalid
–0.2
0.88
0.88
–0.2
1.03
1.03
–0.2
1.15
1.15
CQDOH
CQH
Output Clock (CQ/CQ) HIGH
–
–
–
CQ Clock Rise to CQ Clock Rise
–
–
–
CQHCQH
(rising edge to rising edge)
t
t
t
t
t
t
Clock (K/K) Rise to High-Z (Active to High-Z)
–
0.45
–
–
0.45
–
–
0.45
–
ns
ns
ns
CHZ
CLZ
CHQZ
Clock (K/K) Rise to Low-Z
–0.45
–0.45
–0.45
CHQX1
CQHQVLD
Echo Clock High to QVLD Valid
–0.20 0.20 –0.20 0.20 –0.20 0.20
QVLD
DLL Timing
t
t
t
t
t
t
Clock Phase Jitter
DLL Lock Time (K)
–
0.20
–
–
0.20
–
–
0.20
–
ns
KC Var
KC Var
2048
30
2048
30
2048
30
Cycles
ns
KC lock
KC Reset
KC lock
KC Reset
K Static to DLL Reset
–
–
–
Notes
21. When a part with a maximum frequency above 300 MHz is operating at a lower clock frequency, it requires the input timing of the frequency range in which it is
being operated and outputs data with the output timing of that frequency range.
22. This part has an internal voltage regulator; t
be initiated.
is the time that the power must be supplied above V minimum initially before a read or write operation can
DD
POWER
23. These parameters are extrapolated from the input timing parameters (t
- 250 ps, where 250 ps is the internal jitter. An input jitter of 200 ps (t
) is already
KHKH
KC Var
included in the t
). These parameters are only guaranteed by design and are not tested in production.
KHKH
24. t
, t
, are specified with a load capacitance of 5 pF as in (b) of “AC Test Loads and Waveforms” on page 21. Transition is measured ±100 mV from steady-state
CHZ CLZ
voltage.
25. At any voltage and temperature t
is less than t
and t
less than t
.
CHZ
CLZ
CHZ
CO
26. t
spec is applicable for both rising and falling edges of QVLD signal.
QVLD
27. Hold to >V or <V .
IH
IL
Document Number: 001-06348 Rev. *D
Page 22 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Switching Waveforms
Figure 5. Waveform for 2.0 Cycle Read Latency
WRITE
7
READ
9
NOP
11
NOP
1
READ
2
READ
3
NOP
4
NOP
5
NOP
6
WRITE
8
NOP
10
12
K
t
t
t
t
KH
KL
CYC
KHKH
K
LD
t
t
HC
SC
R/W
A
A1
A2
A3
A4
A0
t
QVLD
t
t
t
SA HA
QVLD
t
QVLD
QVLD
t
t
HD
HD
SD
t
SD
D21 D30 D31
t
Q00 Q01 Q10 Q11
D20
Q40 Q41
DQ
t
t
t
CHZ
CLZ
DOH
t
t
CO
CQD
(Read Latency = 2.0 Cycles)
t
t
CQDOH
t
CCQO
t
CQOH
CQ
CQ
t
t
CQH
CQHCQH
CCQO
t
CQOH
DON’T CARE
UNDEFINED
Notes
28. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, that is, A0 + 1.
29. Outputs are disabled (High-Z) one clock cycle after a NOP.
30. The third NOP cycle between read to write transition is not necessary for correct device operation when Read Latency = 2.0 cycles; however at high frequency
operation, it may be required to avoid bus contention.
Document Number: 001-06348 Rev. *D
Page 23 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or visit
www.cypress.com for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
375 CY7C1246V18-375BZC
CY7C1257V18-375BZC
CY7C1248V18-375BZC
CY7C1250V18-375BZC
CY7C1246V18-375BZXC
CY7C1257V18-375BZXC
CY7C1248V18-375BZXC
CY7C1250V18-375BZXC
CY7C1246V18-375BZI
CY7C1257V18-375BZI
CY7C1248V18-375BZI
CY7C1250V18-375BZI
CY7C1246V18-375BZXI
CY7C1257V18-375BZXI
CY7C1248V18-375BZXI
CY7C1250V18-375BZXI
333 CY7C1246V18-333BZC
CY7C1257V18-333BZC
CY7C1248V18-333BZC
CY7C1250V18-333BZC
CY7C1246V18-333BZXC
CY7C1257V18-333BZXC
CY7C1248V18-333BZXC
CY7C1250V18-333BZXC
CY7C1246V18-333BZI
CY7C1257V18-333BZI
CY7C1248V18-333BZI
CY7C1250V18-333BZI
CY7C1246V18-333BZXI
CY7C1257V18-333BZXI
CY7C1248V18-333BZXI
CY7C1250V18-333BZXI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
Commercial
Industrial
Commercial
Industrial
Document Number: 001-06348 Rev. *D
Page 24 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Ordering Information (continued)
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or visit
www.cypress.com for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Package Type
300 CY7C1246V18-300BZC
CY7C1257V18-300BZC
CY7C1248V18-300BZC
CY7C1250V18-300BZC
CY7C1246V18-300BZXC
CY7C1257V18-300BZXC
CY7C1248V18-300BZXC
CY7C1250V18-300BZXC
CY7C1246V18-300BZI
CY7C1257V18-300BZI
CY7C1248V18-300BZI
CY7C1250V18-300BZI
CY7C1246V18-300BZXI
CY7C1257V18-300BZXI
CY7C1248V18-300BZXI
CY7C1250V18-300BZXI
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm)
51-85195 165-ball Fine Pitch Ball Grid Array (15 x 17 x 1.4 mm) Pb-Free
Commercial
Industrial
Document Number: 001-06348 Rev. *D
Page 25 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Package Diagram
Figure 6. 165-ball FBGA (15 x 17 x 1.40 mm), 51-85195
"/44/- 6)%7
4/0 6)%7
0). ꢀ #/2.%2
Œꢃꢂꢃꢄ - #
Œꢃꢂꢇꢄ - # ! "
ꢌꢃꢂꢀꢈ
0). ꢀ #/2.%2
Œꢃꢂꢄꢃ
ꢅꢀꢆꢄ8
ꢍꢃꢂꢃꢆ
ꢀ
ꢇ
ꢉ
ꢈ
ꢄ
ꢆ
ꢁ
ꢊ
ꢋ
ꢀꢃ
ꢀꢀ
ꢀꢀ ꢀꢃ
ꢋ
ꢊ
ꢁ
ꢆ
ꢄ
ꢈ
ꢉ
ꢇ
ꢀ
!
"
!
"
#
$
#
$
%
%
&
&
'
'
(
*
(
*
+
+
,
,
-
-
.
0
2
.
0
2
!
ꢀꢂꢃꢃ
ꢄꢂꢃꢃ
ꢀꢃꢂꢃꢃ
"
ꢀꢄꢂꢃꢃ¼ꢃꢂꢀꢃ
ꢃꢂꢀꢄꢅꢈ8
./4%3 ꢎ
3/,$%2 0!$ 490% ꢎ./. 3/,$%2 -!3+ $%&).%$ ꢅ.3-$
0!#+!'% 7%)'(4 ꢎꢃꢂꢆꢄG
*%$%# 2%&%2%.#% ꢎ-/ꢍꢇꢀꢆ ꢏ $%3)'. ꢈꢂꢆ#
0!#+!'% #/$% ꢎ""ꢃ!$
3%!4).' 0,!.%
#
51-85195-*A
Document Number: 001-06348 Rev. *D
Page 26 of 27
CY7C1246V18, CY7C1257V18
CY7C1248V18, CY7C1250V18
Document History Page
Document Title: CY7C1246V18/CY7C1257V18/CY7C1248V18/CY7C1250V18, 36-Mbit DDR-II+ SRAM 2-Word Burst Ar-
chitecture (2.0 Cycle Read Latency)
Document Number: 001-06348
Orig. of
Change
REV.
ECN No.
Issue Date
Description of Change
**
425689
461639
See ECN
See ECN
NXR
New Data Sheet
*A
NXR
Revised the MPNs from
CY7C1257AV18 to CY7C1257V18
CY7C1248AV18 to CY7C1248V18
CY7C1250AV18 to CY7C1250V18
Changed t and t from 40 ns to 20 ns, changed t
, t
, t , t
,
TH
TL
TMSS TDIS CS TMSH
t
, t from 10 ns to 5 ns and changed t
from 20 ns to 10 ns in TAP
TDIH CH
TDOV
AC Switching Characteristics table
Modified Power-Up waveform
*B
497628
See ECN
NXR
Changed the V
operating voltage to 1.4V to V in the Features section,
DDQ DD
in Operating Range table and in the DC Electrical Characteristics table
Added foot note in page# 1
Changed the Maximum rating of Ambient Temperature with Power Applied
from –10°C to +85°C to –55°C to +125°C
Changed V
(Max.) spec from 0.85V to 0.95V in the DC Electrical
REF
Characteristics table and in the note below the table
Updated foot note #17 to specify Overshoot and Undershoot Spec
Updated Θ and Θ values
JA
JC
Removed x9 part and its related information
Updated footnote #24
*C
1093183
See ECN
VKN
Converted from preliminary to final
Added x8 and x9 parts
Updated logic block diagram for x18 and x36 parts
Changed I values from 925 mA to 1210 mA for 375 MHz, 800 mA to 1080
DD
mA for 333 MHz, 725 mA to 1000 mA for 300 MHz
Changed I values from 290 mA to 320 mA for 375 MHz, 270 mA to 300
SB
mA for 333 MHz, 250 mA to 290 mA for 300 MHz
Changed Θ value from 12.43 °C/W to 16.25 °C/W
JA
Changed t
max spec to 8.4 ns for all speed bins
CYC
Updated Ordering Information table
*D
2198506
See ECN VKN/AESA Added footnote# 19 related to I
DD
© Cypress Semiconductor Corporation, 2006-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-06348 Rev. *D
Revised March 11, 2008
Page 27 of 27
All product and company names mentioned in this document are the trademarks of their respective holders.
|
Hotpoint E302X User Manual
Hotpoint Cooktop HAGL60P User Manual
Grizzly DVD VCR Combo g0747 User Manual
Eizo EIZO FlexScan L565 User Manual
Cisco Systems Computer Hardware OL 9977 05 User Manual
Atlantis Land A05 17AM L03 User Manual
AOC LM765s User Manual
Analog Devices ADuC812 User Manual
American Dynamics 15 and 17 inch CCTV User Manual
AMD GA K8N51GMF RH User Manual